Order new sling (for mesh sling replacement) Before you get started, you have to measure your chairs and order replacement sling. To find width, measure from the center of one rail to the center of the opposite rail at the bolt locations typically found at the top and bottom of the sling. To find length, lay a cloth tape measure along the top face of one rail so it follows the rail's curvature. Cut the old sling Slash the old sling down the middle with a utility knife. (A damaged sling cannot be saved.) Remove the end cap on each side rail. Remove the old sling Slide the two halves of the sling out of their tracks in the chair's rails. Loosen but don't remove the bolts that attach the rails to the chair frame, then pop out the spreader bar. This is the best time to retouch or repaint your frame. Go to Frame Touch-Up Techniques for how-to and tips. Slide the new sling on Remove one rail entirely. Hold the sling with its hem side to the back and slide its nylon rod into the track of the rail that's still attached to the chair frame.
Secure the new sling Slide the detached rail over the sling's other nylon rod. Bolt this rail back on the frame. Tighten the loose bolts on the opposite rail to make the sling taut. Reattach the spreader bar Reinsert the spreader bar. Use a pipe clamp to spread the rails slightly; if need be, bend the bar a bit to make it fit, then hit it with a rubber mallet to restore its shape. With a wire cutter, trim each rod flush with the end of the rail. Push the end caps back on the rails. You're done reviving your sling chair. Now, see Care and Maintenance tips. Or, click next to see how to replace vinyl straps. Order new straps (for vinyl replacement) For a single-wrap strap (one with exposed plastic pegs or metal clips), measure across the frame from hole to hole with a cloth tape measure wrapping around the outside of the frame. A double-wrap strap (shown) covers the fasteners. Start at one hole, loop the tape measures fully around the frame, then pull to the opposite hole and repeat.
Buy enough straps and pegs to redo the entire piece. (Metal clips can be reused.) The supplier will cut each strap to length and punch a hole for pegs or attach edge clips on both ends. Make the straps flexible by soaking them in hot (not boiling) water; never use a hair dryer or heat gun. Attach the strap end by pushing a peg through its hole and into the hole on the back of the frame. Wrap the strap around the frame With the peg seated firmly, wrap the strap all the way around the frame, covering the peg. (For a single wrap, simply go halfway around the frame and pull to the opposite side.) Stretch the strap to the other side Grab the strap near its middle and stretch it to the opposite side of the frame. Hold it tight against this side with one hand; use the other to loosely wrap the strap's free end around the frame 1½ times. Keep tension on the strap as you push a peg through the free end and into its hole. Slide the loop up over the peg with your thumb, then let go of the strap.
It will tighten as it cools. Repeat this process for all straps. You're done reviving your vinyl strap chair. Now, see Care and Maintenance tips. The time to touch up nicks and scratches on the frame is after the old straps or slings have been removed and before the new ones go on. The method to use depends on the type of metal to be painted. For aluminum, rough up the surface slightly with 100-grit sandpaper, then smooth with 220-grit paper. There's no need to prime—just apply an exterior-grade acrylic enamel paint. Use a tiny touch-up brush on nicks, a spray can on bigger scratches. For wrought iron on tubular steel, use a wire brush and sandpaper to sand any rust spots or chipped paint down to bare metal. Next, brush or spray on a metal primer, then apply an exterior enamel topcoat. (A coat of rust converter such as Rust Reformer stabilizes rust without sanding, but a rough, crusty look will remain.) When a painted frame is covered with scratches or caked with rust, it's probably time for a professional overhaul.
Factory-authorized refinisheers like The Chair Care Co. will sandblast and repaint furniture with a tough, powder-coated finish that will last 15 years or more. "The pieces come out looking brand-new," says owner Steven Gentino. The full-body treatment—blasting, repainting, welding, repairing straps, slings, or cushions, and replacing fasteners—runs about $120 for a typical chair. That's still only one third to half the cost of buying new. Once paint is dry: • Continue fabric sling replacement • Continue vinyl strap replacement The plastic components of outdoor furniture (shown)—vinyl straps, plastic pegs, and mesh slings—last about 10 years. In the meantime, the easiest way to keep outdoor furniture looking good is to give it a quick scrubdown with mild dish soap, followed by a water rinse. In addition, each material has its own particular needs. Straps and Slings__Both are made of vinyl, which suntan oil stains, sunlight fades, and dirt and mildew stick to like magnets.
A spritz with a vinyl cleaner such as FeronClean or a mild all- purpose cleaner like Fantastik or Formula 409 and a swipe with a cloth is the best way to remove grime. Never use abrasives, bleach, or ammonia, all of which strip vinyl of its UV protection. Exposure to pesticides and fertilizers does the same thing. Encourage sunbathers to cover chairs with a towel. Metal__Touch up the paint as soon as it's nicked. Do not apply car wax, which will leave a cloudy buildup. Storage__The best place for furniture in the winter is a dry spot indoors. If it must remain outdoors, wrap each piece in a breathable vinyl cover (available at outdoor-furniture distributors) that doesn't touch the ground. That way, moisture can escape, preventing mildew and rust.Home » Recover deckchairs How to Recover a Traditional Wooden Deckchair Traditionally deck chairs were re-covered once a year. After summer use and winter storage in often damp, cold conditions in a shed or garage your deckchairs will probably be looking a little tired.
Fortunately, with just a few simple tools and available from The Stripes Company re-covering a deckchair is simple and quick. In the video 'How to Recover a Deck Chair' below Maria from The Stripes Company shows you how ! Please call us on 01244 336 387 if you need any additional help or advice after watching If you prefer to read how to recover a deckchair use the images and instructions below How to Recover a Deckchair Step 1 - You will need 1.5 metres Deckchair Canvas Fabric - see our range of in over 40 different Stripes! Stripes must be vertical 20 + Upholstery Tacks Step 2 - Deckchair Frame Position 1 Place frame upside down on a table - Note the position of the ridges – ridges on underneath 2 Start at the top - The wide end - with 1.5 metres fabric 3 Feed fabric underneath bars a & b - Fold over edge of fabric 3-4 cms 4 Roll fabric back over bar 'a' Step 3 - Attach Fabric Wide End 1 Starting at one edge insert upholstery pin on underside of bar.
Hold pins between two fingers as in pic 2. Gently hammer till it bites. Remove fingers, hit it hard till pin head flush with fabric (pic 3) 2 Next put a pin in the centre, hammer in 4 Next put in pin at other end 5 Repeat - Fill in with the remaining pins - 9 /10 in total Step 4 - Attach Fabric Narrow End 1 Feed rest of fabric underneath bar at narrow end 2 Turn the fabric in so that it fits inside frame 3 Fold over end of fabric (cut off if too much) 4 Fold over bar and secure as before Because our fabric is 100% natural cotton with no synthetics, the weave is constructed to slightly 'give' when first sat on. If tacked on tightly - the canvas will 'mould' to the shape of the body to give a more relaxed and comfortable seat. This is totally normal and the strength of the fabric is not compromised in any way. 100% Woven Cotton45cms width unless otherwise stated in product description.Multiples of one colour come as a complete length - if you have more than one deckchair, try covering them in different clashing colours!