Take a look at more products! Our Exclusive Stain Gallery Take a look at real application photos of our products! Not All Great Works of Art are Found on Walls From the Art Museum in Seattle to the North Church in Boston... from malls to gyms to homes... fine hardwood floors become works of art with DuraSeal® products. Durability with aesthetic appeal - that is what DuraSeal® products have come to signify in the wood flooring business. Our product line includes stains with a high solids content for deep color and exceptional sealing action, and transparent finishes that withstand brutal wear and punishment. Because the job doesn't always end with the finish, DuraSeal® also provides a full line of maintenance products. This selection and quality have made DuraSeal® products the number one choice among flooring contractors. So whether you need to stain, finish or maintain a hardwood floor, DuraSeal® has a complete line of quality products to bring out the artist in you.
Finish and Curing Parameters In general, finishes perform best at temperatures of 65 - 80 degrees (F) 19- 28(C) and Relative Humidity at 40% to 60%. Finishes generally do not perform well when... Temperatures are over 90 degrees (F) 32(C) Temperatures are under 50 degrees (F) 10(C) Relative Humidity is over 90% RH Relative Humidity is under 30% RH Products You Can Rely On Floor Finish Adhesion Failure is a Profit Taker You, the retailer/contractor, have just installed and finished (or recoated) a beautiful hardwood floor. The owner is pleased, which means that the final installation transaction - your final payment is about to take place. Under 125 g/L VOC. Exceptional flow and leveling. Single component, no waste. Available in Satin, Semi Gloss and Gloss sheens.We’re not going out on a limb when we say hardwood floors are one of the most popular, value-adding features in your home. But hardwood floors need regular maintenance and refinishing to keep them looking spiffy.
How much wear and tear your floors get determines how often you need to refinish them and what product you use. A household with just two adults might only have to refinish every 10 years; a home with adults, kids, and a dog might need to refinish every three to four years.There are a lot of finishes out there. Use our at-a-glance guide below to choose the one that’s right for your home. We also help you decide if you want to refinish floors yourself.Wax is the time-tested, old-fashioned way to refinish wood floors and was routinely used before polyurethanes became available in the 1970s. Both paste and liquid versions are making a comeback with homeowners who want a mellow, low-sheen look, and with those who prefer to use natural products with low VOCs and toxicity.It’s applied by hand working small areas at a time, which makes it DIY-friendly (but labor-intensive). It’s also easy to touch up a wax finish, so ongoing maintenance is simple.If you don’t want to darken your wood (which wax tends to do), first apply a base coat of shellac or sanding sealer that penetrates and seals the wood.
Two to three coats of wax are recommended.Especially good for: antique flooring in historic homesCost: $10 to $25 per 1 pound covers 400 to 500 square feetPolyurethanes are today’s standard floor finish. Water-based varieties used to have a reputation for being eco-friendly (still true) but not as durable as regular polys. However, today’s water-based polys are nearly as tough as their oil-based cousins.One difference is final color: Water-based polys dry clear; oil-based polys have a slight amber tint.Water-based polyurethane has very low VOC content and is easy for a DIYer to apply. Three to four coats are recommended. You can use a water-based polyurethane over an oil-based poly as long as the old finish has completely cured (two to three weeks).Especially good for: eco-conscious DIYersCost: $40 to $60 per gallon covers 400 to 500 square feetOil-based polys are the mainstay of floor finishing and widely used by professional finishers.Although they’re tough, long-lasting, and less-expensive than water-based polys, oil-based polys have a higher VOC content and stronger odor during application.
A coat takes 8 to 10 hours to dry, so you’ll want to vacate your house until the floor is completely dry — and bring your pets with you. Two to three coats are recommended.Professional floor refinishers report some problems when using an oil-based poly over a water-based poly. Best advice: Don’t do it.Especially good for: professionally finished floors at a reasonable priceCost: $30 to $40 per gallon covers 500 to 600 square feet; it’s $1 to $2 per square foot to have a pro do it.The Cadillac (or Volvo) of floor finishes, acid-cured Swedish finishes are for pro application only. They’re among the toughest of all hardwood flooring finishes, and the most expensive. They’re sometimes called conversion varnish sealers.Acid-cured finishes have extremely high VOC content; you’ll have to bunk elsewhere for a few days after finishing to give the odors a chance to clear. The finish takes up to 60 days to fully cure, but you can walk on it after three days. Keep furniture off for two weeks, and rugs off for the full 60 days so the fibers don’t stick.
Especially good for: high-end homes with flooring made from exotic woods and floors with elaborate inlay designsCost: $3.75 to $5 per square foot professionally appliedThis is a durable finish that’s a step up in toughness and longevity from water- and oil-based polyurethane. It’s tricky to apply and isn’t recommended for DIY — it dries very fast, so speed and a deft touch are needed to avoid lap marks.It has a high VOC content, making a respirator and good ventilation a must during application. Homeowners and pets should vacate the house during application and for up to two weeks afterward.Especially good for: high-traffic areas and homes with multiple kids and dogsCost: $2 to $4 per square foot professionally appliedOil sealers have been used for centuries to protect and moisture-proof wood. They’re easy to apply, and spot touch-ups are a snap. Because it penetrates the wood, an oil sealer enhances grain patterns and deepens the color of the wood. The finish itself doesn’t scratch, but recoating usually is needed every two to three years as the finish wears down.
The basic ingredient is tung oil, a naturally occurring, low-VOC oil that hardens as it dries. It needs long drying times between coats (24 to 48 hours), so finishing a floor with the recommended three coats can take several days.Especially good for: historic homes with antique flooring; DIYersCost: $60 to $70 per gallon covers 500 square feetThis super-tough finish only comes on prefinished wood planks. You won’t apply it yourself, but you’ll need to know it’s there if you ever decide to refinish it. It requires special refinishing techniques, like sanding with milder grits before using heavier grits. Your floor refinisher can determine if your flooring is covered with an aluminum oxide coating.Polyurethane floor products have surpassed the usefulness of this time-honored wood finish. Houses built before 1970 may have hardwood floors finished with shellac, and you can maintain and refinish them with another coating of shellac. It’s not compatible with more modern finishes, such as polyurethane, so only refinish shellac with wax or another coating of shellac.
Test for shellac by dribbling a few drops of water on an inconspicuous spot. If the finish turns milky white, it’s shellac.Shellac is a natural product that’s non-toxic and produces few VOCs. It’s not as tough and durable as polyurethanes, and is susceptible to stains from water and other spills. However, it’s easy to repair scratched areas by rubbing out the scratches with denatured alcohol, then reapplying shellac.Shellac pairs well with wax. Use shellac as a base coat, and finish with two or three coats of hand-rubbed wax.Especially good for: refinishing antique floors already coated with shellacCost: $80 to $90 per gallon covers 300 square feetDoes your floor need a touch-up or an overhaul?1. For surface scratches and normal wear and tear, lightly sand the finish (called screening) and apply a new topcoat. You’ll want to use the same type of finish product that was on your flooring originally.2. For more damaged flooring, you’ll want to completely sand the old finish off down to the bare wood.