“Creativity is a wild mind and a disciplined eye ” A clever illusion of space 08TH February / PRESS 14-Page Case study on one of our newest projects. Barbara Genda Furniture talks to KBB about creating a truly bespoke solution that maximises storage, stays within budget and doesn’t compromise on design.Edit ArticleHow to Build a Closet A closet is often the most under appreciated room in a house - until you need one. Then the storage space it represents becomes a valuable asset. It does not take a professional to build a closet only a willingness to set aside some time and have access to both hand tools and basic power tools. Decide where to locate your closet. Lay out the walls and doors. Remove any base or ceiling trim and carpet from the area you have laid out for construction. Install the framing, beginning with the base and top plate. Attach the base with deck screws to the floor and the top plate to the ceiling. Use 4-inch (10.2 cm) toggle bolts and construction adhesive.
Nail or screw the end studs to side walls and to the top and base plates and rough in the door opening by nailing the studs to the top and bottom plates. Studs traditionally are on 16 inches (40.8 cm) spacing. Just use the spacing you have if width of your wall is greater than 16 inches (40.8 cm) but less than 24 inches (61.2 cm). Split the difference for better support of the sheathing if the width is greater than 24 inches (61.2 cm). Rough in the door framing. This will include trimmer studs on each side of the door. Dimensions are normally 6 feet (1.8 m), 10.5 inches (1.83 m x 26.7 cm) tall attached to the wall studs and a doubled 2 x 4-foot (5.1 X 10.2 cm) door header nailed to the door trimmer with the end nailed to the wall stud. Place short studs (called cripples) between the door header and ceiling plate. This will normally be centered on 16 inches (40.8 cm). The framing is complete. Hang .5-inch (1.27 cm) sheetrock or sheathing on the walls. Both sides of the framing use sheetrock screws.
Cut sheetrock to size using a utility knife and a straight edge as a guide. Run the edge of sheathing to the roughed-in door openings. Score the sheetrock with a utility knife. Begin breaking the sheetrock off with hand pressure and then with a straight edge (along the back side of the sheetrock). The sheetrock should snap off in one piece if it is scored deep enough. Position the doors in the closet. How to do this will depend on the type of doors chosen. Insert the door into your rough opening, if you are using a traditional prehung door (as for a walk-in-closet). Then, with a level, plumb the door using shims to keep it aligned. Install the trim supplied by the manufacturer around the door. The use of a bi-fold door requires that you first trim out the door opening. Use trim similar to the floor trim you salvaged or that matches the trim in the room. Hang the door in place and adjust to fit, following manufacturer's instructions. Install the accessories, however elaborate or simple, that fit your needs.
Show more unanswered questions A good way to see how the space for the closet and the room fit together is to chalk out the closet walls, then place any needed furniture to see if it works. Check to see the width and height requirements for the rough opening for the door you've chosen (when using prehung or bifold doors). Prehung doors are the easiest to install in that they come with all of the hardware installed and with the trim to go around the door. These are available at most home improvement stores. Make sure that there are no existing electrical lines or plumbing in the way before installing or drilling into any existing walls. You will probably not need a building permit to install a closet. However, if you are adding electrical lighting or plugs, you may need an electrical permit which requires a licensed electrician to do the work. Check your local building codes. Our various door styles available… Our wide variety of colours & finishes…
Small recessed pockets of space, called alcoves are an unavoidable fixture in most homes. In older homes, the construction itself warranted such spaces to be created which was often used as hidden storage over which a curtain would be placed. Modern homes still carry alcoves, but now they are designed as a focal point of interior decor. Living rooms make the most of alcove storage. They can either store books, nick knacks or can be converted into recessed storage for gadgets and other tech media. Home offices use alcoves to create cabinet storage, whereas bedroom alcoves can be converted into storage of blankets and other clothing. There are several ways alcoves can be a big blessing in homes and here are 9 quirky ideas to enhance the alcove space. Rather than placing customized bookshelves that jut out and occupy space, alcoves provide a ready storage space for books. They just need to be fitted with sturdy shelves and there’s more space than any book lover can have.
Ready-made floating shelves are a great option. They can be fitted to create a staggered storage for alcoves for books or collectibles. They also prevent the space from looking too cluttered. Home offices can do with all kinds of storage especially since things can get messy very often. By using slim shelves and wooden doors, the alcove space can be kept neat and uncluttered, perfect for storage. Alcoves in kitchens can be covered with a glass door and converted into a display nook for cutlery and frequently used items. Opaque glass keeps the room looking clean and uncluttered. Storing linen can be quite a task because bedlinen and clothing often overflow. A convenient alcove space helps you display your good stuff, plus the shelves keep everything well organised. Kids love little hole in the walls, and alcoves in any part of the home are perfect little spaces to create a study corner. They can do their homework, read and be creative, all while you watch over them.