There are many doorknob hardware designs. question asked most often is how to remove interior doorknobs withIt's more obvious how to remove the styles withThis explanation covers only one type with the approach is much the same for many others. The last Figure, at the bottom of the page, shows theYou may want to take a look at it before The first step is to remove the knob on one side The knob is held on by a spring loaded thin detent (button) on the backside of the knob. The knob on one side or the other has the detent. You press on this detent and pull the knob off with the detent depressed. Figure 1 shows a narrow blade screwdriver being used to depress the detent to release the In this case the detent was located on the bottom, but it can be located anywhere around the barrel of the knob. Figure 2 shows the keeper slot (hole) the detent snaps into to hold the Next, remove the trim ring/cover. Figure 3 shows using a wider,
thin-blade screwdriver to pry off the trim ring. In Figure 4 you see a small notch in the trim This notch should usually be located at the bottom as shown by the screwdriver tip in Figure 3. Depending on who put the trim ring on last it may be in almost any position. rings don't have a notch. In these cases you should still try to slip/work the screwdriver (or a table knife) under the ring at the bottom as shown. You may mar/scar the door with the tool while prying the cover off -- by working at the very bottom of the cover the scar is less likely to be noticeable/visible. From this point on, the procedure is prettyRemove the clamping screws, the actuating shaft assembly and the far knob, then follow the steps in the following figures. If the steps still aren't clear let me know and I'll try to improve this page. Pull Out Latch AssemblyRemoving An Interior Doorknob No need to call in the pros for a faulty lockset
You don't need a locksmith to replace a faulty lockset on an interior door. It's a simple job anyone can tackle in less than 15 minutes. For many novice do-it-yourselfers, however, the most difficult part is the first step: removing the doorknob. On most locksets, the mounting screws are concealed, so at first glance there doesn't seem to be a way to disassemble the knob. Here's the secret: Look closely at the shank of the interior doorknob and you'll see a tiny slot or hole. Push the tip of a narrow-blade screwdriver or nailset into the hole. Tug on the knob and it will slide right off. Then pry off the round decorative plate, called the rose, to expose the screws that hold the lockset onto the door.Refinishing Door KnobsHow To Paint Door KnobsOld Door KnobsPaint Metal DoorRefinish Cabinet DoorsDid Cabinet DoorsOld HingesKnobs HingesStrip HardwareForwardRemoving years of bad paint decisions from hinges and door knobs. Easy as water, heat, and baking soda. I actually did this in my old bungalow.
Really very easy, butr emember, metal gets hot people.... I may or may not have burned myself.Edit ArticleHow to Paint Porcelain Knobs Four Methods:Preparing the Knobs Before PaintingChoosing a Color Scheme and DesignUsing Porcelain Craft PaintsUsing Primer and PaintCommunity Q&A You may want to paint porcelain knobs to update an outdated decorating scheme, hide blemishes to the knobs' finish, or to personalize the knobs on your furniture or cabinetry. You can use craft paints specially designed for use on porcelain that require firing in your oven to cure the paint, or you can use a combination of primer and paint when painting porcelain knobs. Wash the porcelain knob or knobs that you want to paint. A clean surface free of dirt and grime will allow the paint or primer to adhere better to the porcelain knob. Remove the screw from the knob and set aside. Wipe the knob thoroughly with soapy water using a lint-free rag. Wipe with denatured alcohol. Allow the cleaned knob or knobs to dry.
Prepare an area for painting the knob. Make sure there is adequate ventilation and ample room for all your painting supplies. Consider using a piece of craft foam to keep the knob in place during painting. Screw the screw back into the knob or knobs, and push the screw portion into the piece of craft foam until the foam is flush with the bottom of the knob. Decide on a color and design for painting the knob. The effect you wish to achieve will influence which painting method you choose for painting your porcelain knobs. Consider using craft paint designed for use on porcelain if you want the original color of the knob to show and you want to paint a design on the knob. Craft paint is available in liquid form that requires you to use a brush and in marker form which may make detail work easier to execute. Look at fabric and wallpaper designs for inspiration. If you want to paint a pattern on your porcelain knob, small scale designs will work best. Plan to use a combination of primer and paint if you want a uniform finish and color on your porcelain knobs.
You can use latex, acrylic or oil paint over the primed knob, and this provides you with a greater option of colors and finishes to choose from than if you use porcelain craft paints. You can also use spray paint over primer in addition to brushing on the paint of your choice. Sketch out your chosen design on graph paper. If you choose to paint a pattern or design on the knob, sketching out the design to scale before painting can help you produce a more uniform and professional looking result. Measure the diameter of the porcelain knob you want to paint. Draw a circle on the graph paper with the same diameter. You can use a compass and pencil if you are not comfortable sketching the circle freehand. Divide the circle into quadrants by drawing 1 vertical line and 1 horizontal through the center or the circle. Sketch out the design you plan to paint on the knob. Gather together any paints you plan to use on the knob. Make sure you have a paintbrush available for each color if you don't want the paint to dry while you are cleaning your brush when you switch colors.
Choose soft, natural fiber paintbrushes when using porcelain craft paints. Examples include red sable or squirrel hair quill brushes.Use your paintbrushes or porcelain craft paint in the marker form to apply the paint to the knob. Allow your work to dry after you finish with 1 color if you are worried about having different colors bleeding together and mixing while you paint. Resume painting with the next color once the first color has dried. Heat your oven to 300 degrees F (148.9 degrees C). Place knobs on an oven safe baking sheet or pan with sides. Insert the pan into the oven and allow to fire for 30 minutes. Remove the pan from the oven. Apply an oil based primer to the knob or knobs you wish to paint. Oil based primer will adhere better to the glossy surface of a porcelain knob and will be more resistant to scratches. Look for a primer designed for use on glossy surfaces. Avoid using latex primer, as it may scratch off the surface of the knob.
Apply primer using a paintbrush or small foam roller. Apply a light coat to ensure a more even coat and smoother results. Allow the primer to dry. Apply an additional coat of primer if needed. Paint the knob using your chosen paint. Apply solid colors using either a paintbrush, small foam roller or spray paint. Use a paintbrush to add detail of your pattern or design if desired. Sand lightly with fine grit sandpaper after the first coat of paint if you are painting the knob a solid color and want to achieve a smooth texture. Apply a second coat of paint. Allow the paint to dry completely. Apply a clear varnish to the painted knob. Varnish will protect the painted surface from damage. Choose a varnish compatible with your paint. Use water-based varnishes for latex or acrylic paint and varnishes especially for oil paint if you used oil paint. Consider what type of finish you want when choosing your varnish. If you want your porcelain knobs to have a glossy sheen, choose semi- or high-gloss.