It looks like nothing was found at this location. Maybe try a search?Secure your garage by changing the door code from time to time. If you think someone knows the code to open your garage door or your remote has been stolen, it is time to change the code on your garage door opener. Newer garage door openers have a keypad in addition to the remote, which makes it slightly easier to change the code. If you have an older garage door that is only operated by a remote, you must physically move the switches inside the remote and door opener to change the code. Place a ladder beneath the garage door’s motor unit to reach the unit. Press the learn button located on the side of the motor and hold it down. Release the button when the light beside it goes out to remove the old code from its memory. Push the learn button on the motor again, so its light comes on again. Enter the desired code on your keypad on the garage wall. The motor unit’s light blinks to indicate that the new code has been accepted.
Press the learn button on the motor once more, so the light on the motor lights up again. Press a button on your remote. The motor unit’s light blinks to indicate the remote has been programmed with the new code. Repeat this step to program all other remotes. Take the cover off of the garage door’s remote control to expose the switches inside the remote. Repeat to change the code in all additional remotes. Move the switches inside the remote to change the code. Replace the cover on the remote control. Place a ladder beneath the garage door’s motor unit. Move the switches on the motor to change the code to match the code in the remote control. /Getty Images Suggest a CorrectionBelow is information to help you program your Garage Door Operator remote control or outside keypad. If you need additional help, feel free to give a call for assistance or to schedule a service call to program for you. CHAMBERLAIN / LIFTMASTER / SEARS CRAFTSMAN GARAGE DOOR OPENERS Programming 971LM and 973LM, 371LM and 373LM Security Plus Transmitters
LIFTMASTER AND SEARS CRAFTSMAN WIRELESS KEYPADS 976LM, 377LM Security Plus and 66LM Wireless Keyless Entry Systems The square smart button is located on the side or the back of the motor head, and is colored red, green, amber, orange, or purple. It is directly under the #1 wire terminal screw. Programming Genie Intellicode Remote Transmitters ** To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2. These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. The receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work.
Genie has been making the 390 MHz frequency exclusively for the last 15 years. These garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. The small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). The small left switch is for programming purposes. To program a button for one of your doors, follow the instructions below: Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK (works with remotes having 9 or 12 internal code setting switches. Keypad is black with a slide-up cover showing the Genie logo only) This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart.
Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers. Door Code in Step #4: ____ ____ ____ ____ Model 1: Intellicode Model GWKIC, ACSDG (black with slide-up cover and the word “Intellicode” printed on the cover) GWKIC, ACSDG, Two Part, Step-By-Step Programming To Reset the Intellicode Wireless Keypad To Program the Intellicode Wireless Keypad NOTE: If red indicator light does not blink, it is not taking the programming steps. Check the 9 volt battery under the keypad numbers. To access, press inward, under the number pad lip while sliding downward to expose the battery. Press the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head.
When pressed, a radio signal indicator will start blinking red for 30 seconds. Adding More Doors to Keypad: With most Genie units, remove the light lens globe to expose the Learn Button on the motor head. The learn button is sometimes located on the back of the unit, or with Accelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first. The Learn Button can be found not far from this antenna. See Troubleshooting Guides for Accelerator photo. Intellicode Model GWKP (off-white with flip-up cover) Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below: Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage. It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver cover must be removed to access the Learn Code button and the indicator LED.
Follow Steps 1 through 3 outlined below: Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN: HOMELINK IN-CAR REMOTE PROGRAMMING INSTRUCTIONS To program a built-in-car transmitter to a rolling code garage door opener (Genie rolling code is called Intellicode, Liftmaster/Sears is called Security plus), you should take the following steps. Programming a Fixed-Code Device (Majority of units made prior to 1996) These devices have internal dip-switches located near the battery of your remote. Programming a Rolling Code Garage Door Opener If your in-car (UHR) remote has 3 LED lights, one above each button, you should follow the instructions below to program your Rolling Code Garage Door Opener. Programming a Fixed Code Device (Majority of units made prior to 1996) Below is a picture of a typical 12-switch DIP switch layout located on your hand-held remote control under the battery cover (your remote may have 8-12 DIP switches).