This durable and fade-resistant carpet comes in a variety of colors and styles Add a the feel of artificial grass to your outdoor living areas All-weather carpet solutions for pool decks, boats and docks Were you looking for a specific type? Choose a category to narrow your search.For easy-to-clean, fade- and stain-resistant carpet, choose material made from UV-resistant olefin fibers. Indoor-outdoor carpet is available in varying grades of quality, color and weave. Do the touch test-the thicker the carpet feels, the higher the grade and durability. For areas that are prone to dampness or fully exposed to weather, make sure the carpet has an all-weather "marine" backing for moisture resistance. Indoor-outdoor carpet is very easy to install on a prepared surface. For the best results, install carpet when the temperature is between 55 F and 95 F and the humidity is between 10 percent and 65 percent. Use two-sided tape for lower grade carpet and indoor-outdoor adhesive for higher grade.
Unroll the carpet in the place where it will be installed and allow it to expand for one hour. For double-sided tape installation, place double-sided tape around the edge of the room and place a 6"x 6" X every 2 feet on the subfloor. Leave the protective paper on the topside of the tape. Center the carpet in the room. Position the carpet, allowing the edges to curl up against the wall. Remember to allow 3" on each side for trimming. Trim around outside corners and protruding objects by making a vertical slice down the carpet. Cut the carpet from the top down to where it touches the floor. To fit inside corners, cut the carpet in V-shaped cuts where it overlaps. Work your way down carefully, making several V-cuts until the carpet rests flat. For rooms requiring seams, make sure the pile runs in the same direction to avoid apparent discoloration. Overlap the two pieces at least 2". Make a double-cut seam. Use a straightedge and sharp utility knife to cut a seam through both layers at the same time.
Discard the cut strips. Starting from the wall, fold half of the carpet back without disturbing the bottom half. If you choose to use adhesive for permanent installation, use a notched spreader to apply indoor-outdoor adhesive to the subfloor. Always follow the manufacturer's instructions. Slowly unroll the carpet into place over the adhesive. Smooth any bumpy areas. Repeat for the bottom half. For installation using double-sided tape, remove the protective paper from the tape and fold the carpet back into place carefully. Repeat for the other half. Use a 50 lb. carpet roller to properly adhere the carpet to the adhesive or tape. Use a sharp utility knife to trim the edges of the carpet. Hold the knife parallel to the floor. Trim around the entire perimeter of the room. Tuck the carpet under the wall. Good to KnowClip any loose yarn ends in the carpet to avoid unraveling. Apply seam adhesive at the seams and butt the seams together. If a slight buckle forms, work it out by pressing the seams together or rolling the area.
Good to KnowAdhesives and vapors are flammable. Extinguish pilot lights, cigarettes, or other sources of open flames before applying. Clean off any excess adhesive with a mild solvent following the manufacturer's instructions. Walk along the edges of the room to ensure proper adherence. Use a metal binder strip or aluminum saddle to create a threshold to connect one room to another.Compare Low price one off pet non woven waterproof outdoor commercial carpet mat with different colors Shandong Shenghong New Material Technology Co., Ltd. US $0.1-1.2 1000 Square Meters Transaction Level Forest Green Textured Indoor/Outdoor Carpet Item # 362964 Model # 362964 Actual item may vary in color from screen representation for pricing and availability. Limited fade warranty only Great for decks, porches and patios Cleans easily with household detergent and water Not designed to be loose laid; carpet must be installed - this product can be installed over pad (four way power stretched - use seam sealer tape) or as a direct glue down;
this is not a rug and is not bound - the carpet must be installed properly Appropriate for residential use Manufactured in the United States of America 100% high UV olefin fibers Direct glue-down installation recommended for outdoor use; however can be installed indoors over pad but must be four way power stretched and seam tape must be used Face Weight (ounces per square yard) Community Q & A Coronet Stock Carpet Gray Berber Indoor/Outdoor Carpet Item # 97913 Model # ST103-830-1200-MB 2-year limited indoor wear and fade 2-year limited outdoor fade 100% UV Stabilized Olefin Made in the USA All weather non skid marine backing TEC® Skill Set™ Outdoor Carpet Adhesive is specially formulated for the installation of most outdoor carpets and synthetic grass with backings such as marine grade, ACTIONBAC®, rubber-backed, and non-backed. It is water resistant when cured and is for use indoor and outdoor. Buy at Lowe's >
Be the first to review this product. *Email (will not be published) Discover your design personality. And the perfect products to show it off. Other Floor Bonding Products Vinyl Composition Tile Adhesive Premixed Vinyl Tile Grout General Use Multi-Floor Adhesive Releasable Vinyl Floor Tape Releasable Pressure Sensitive Adhesive 1 quart (946 mL) plastic pail 1 gallon (3.78 L) plastic pail Follow carpet manufacturer's recommendations. • Fully cured concrete (on, above, or below grade) which is free from hydrostatic pressure and moisture vapor emissions • Exterior grade plywood Freeze/thaw stable to 10°F (-12°C). If frozen, slowly bring to room temperature and stir before using. Maximum of 18 months from date of manufacture in unopened container. 20-30 min at 75 degree F/ 50% RH Surface must be sound, smooth, clean and dry. Any cracks and depressions must be patched using a cementitious patching compound.
Ensure that the surface is free of waterproofing compounds, sealers, curing agents, oil, grease, wax, adhesive residue or any other contaminant that may impede adhesion. All concrete substrates must be tested for moisture and pH prior to flooring installation. The industry standard methods for testing moisture are ASTM F-2170 (RH) or ASTM F-1869 (Calcium Chloride-Consult floor covering manufacturer for acceptable RH or MVER. Test for pH in accordance with ASTM F-710. pH range of 7-9 is required. Moisture vapor emissions not to exceed 3 lbs./ 1000 ft2/24 hours (0.015 kg/m2/24 hours). IMPORTANT: Refer to flooring manufacturer’s installation guidelines for proper application instructions, including trowel size and approximate coverage. Lack of adhesive due to improper trowel size can contribute to bond failure / inadequate bond. Apply only the amount of adhesive that can be covered in 20 minutes. Direct sunlight accelerates adhesive drying time and can minimize the adhesive transfer to carpet backing.