This tutorial will show you not only how to remove and install a bathroom faucet (it’s not as hard as you might think!), but it will also show you a way to change from a three-hole faucet to a single. One option for this switch is to use a deck plate, which is included with many faucets. While this tutorial shows a different strategy for what happens with the faucet on top of the countertop (check out this article on creating a faux marble countertop for details), the method of hooking up the water for the plumbing will be the same. (You can also check out this tutorial for removing and installing a kitchen sink faucet.)Start by turning off the water under your bathroom sink. Have a bucket handy, because you will have some water leak out when you go to unhook the hoses.Turn off both the hot and the cold water valves. Also, while you’re down here, unhook the sink stopper.Pull the sink stopper out so it’s out of your way. Chances are, your space is limited underneath that small bathroom sink, so any opportunity you have to remove something to clear out some space is an opportunity you should take.
Turn on the faucet handles to let any residual water drain into the sink.Use a crescent wrench to unscrew the hoses.If you have a plastic connector, unsnap the plastic guard.Then squeeze the two plastic tabs on the sides, and pull the connector off.Securing each component of the faucet (the handles and the faucet itself) will be a nut of some sort, screwed into place. Use a screwdriver to loosen these screws.Then twist the brass nut counterclockwise to unscrew it as well.Twist it until it comes all the way off. You’ll notice a rubber O-ring. This should be removed as well.Pull off all components that were holding the handle into place from the underside of the countertop. Repeat for the other handle.Use your crescent wrench to unscrew the large nut that secures the faucet (and accompanying plate) into place.With all of the under-counter components loosened and removed, you can now remove all your faucet parts. Pull out the faucet.Pull off anything else from the countertop so that all you are left with are your exposed faucet holes.
Make any changes to your countertop you wish (here’s an idea for faux marble with concrete, as well as a transition from a three-hole faucet setup to a single hole), then get ready to move onto your new faucet installation.The faucet we’ll be installing today is called a Jaida. It’s a single-hole faucet with a pop-up drain.Remove the faucet from the box. From the mounting bolt, unscrew the nut and remove the mounting plate.At this point, it’s a good idea to identify which of the copper pipes is for hot and which is for cold. These should be labeled. In this case, the longer pipe is hot.Grab your plumber’s putty. This will go on the rubber O-ring to seal the space between the countertop and the rubber ring. (On top of the rubber ring is the faucet itself.)Take little bits of plumber’s putty at a time and fill the groove on the bottom of the rubber seal.Place the seal and faucet on the countertop, threading the pipes and mounting bolt down through the countertop hole.Try not to move the rubber seal much after placing it, to ensure that the plumber’s putty stays put.
Do a preemptive straightening of the faucet, although you’ll need to come back to it a little later in the process to make sure it’s completely straight.On the underside of the countertop, replace the mounting plate (bumps toward the countertop so as to improve “grip”) and nut. Don’t crank down too hard on the nut at this point, although the faucet should be able to stand up securely on its own after tightening the nut underneath.Take one of the adapters and one of the pins. These will attach to the end of either the hot or cold pipe (coming out of the faucet), allowing you to later connect the house’s hot or cold water source to the faucet.Pop the adapter onto the pipe, threaded side down. Position the pin to hold it securely in place. Repeat for the other adapter, pin, and faucet pipe.Attach Teflon tape to the threaded end of one of the adapters. This helps to solidify the seal, when you go to connect the water, to prevent leaking.Using a plumbing hose extension (which should be already attached to your water sources from when you removed your faucet originally), connect the appropriate water source to the Teflon taped adapter.
Hot water generally comes from the left, cold water from the right.Repeat for the other adapter and hose: Teflon tape, adapter, hose. Although the water should still be off at this point, you’re all hooked up.Because the Jaida faucet comes with a pop-up drain, we’ll need to remove the old drain in order to install it. Begin by removing the drain lever under the sink.Then loosen the nut that connects the drain pipe to the sink itself. This will probably require a wrench.Unscrew the nut enough so that you can push upward on the drain.Have a helper grab a pair of pliers. While one person gently pushes the drain pipe upward, the other person will grab the drain ring from in the sink and pull it out.Remove the drain ring completely. We never said this job would be glamorous.Unscrew all the pieces under the sink from the drain pipe down to the P-trap (but don’t remove the P-trap). This will likely include the drain pipe and then another black plastic coupler pipe with two black rings, one on top and one on bottom, and plastic seals.
You can get rid of the drain pipe, but you’ll want to keep the black coupler pipe (assuming it’s still in good shape). Wash all components, then replace it back onto the P-trap.Thoroughly clean the sink drain hole.Place the new pop-up drain into the sink drain hole. Straighten out any words or logos on the drain, if that sort of thing is important to you.Before you push the drain all the way down onto the black coupler pipe, you’ll need to thread the new drain pipe down through new plastic seal and “nut,” in that order.While one person works the new seal up toward the bottom of the sink, the other person should hold the drain in place above in the sink.Screw on the new “nut.” Again, someone should be holding the drain in place, particularly if you’re trying to keep any words or logos straight.Affix the black coupler pipe (also could be thought of as the P-trap extender pipe) to the new drain pipe.When everything is tightened, check out the new pop-up feature of your drain.