200FD Bi-Fold Door Hardware 125lbs [57kg] Max Panel Weight Each 48" [1219mm] Max Panel Width Each 108" [2743mm] Max Panel Height 1-1/8" [29mm] to 1-3/4" [44mm] Panel Thickness Top Mount Hanger Type Commercial Grade Top Hung Bi-Fold Door Hardware 200FS Side Mounted Bi-Fold Door Hardware 1-3/8" [35mm], 1-3/4" [35mm], 2-1/4" [57mm] Panel Thickness Side Mount Hanger Type 100FD Bi-Fold Door Hardware 75lbs [34kg] Max Panel Weight Each 24" [610mm] Max Panel Width Each 1" [25mm] to 1-3/4" [44mm] Panel Thickness 100FS Side Mounted Bi-Fold Door Hardware 1-1/8" [29mm], 1-3/8" [35mm], 1-3/4" [44mm] Panel Thickness 111FD Bi-Fold Door Hardware 50lbs [23kg] Max Panel Weight Each 3/4" [19mm] to 1-3/4" [44mm] Panel Thickness 1700 Bi-Fold Door Hardware 40lbs [18kg] Max Panel Weight Each 96" [2438mm] Max Panel Height Residential Grade Top Hung Bi-Fold Door Hardware 1700FS Side Mounted Bi-Fold Door Hardware
3/4" [19mm], 1-1/8" [29mm], 1-3/8" [35mm] Panel Thickness 1825 "Tap-In" Bi-Fold Door Hardware 35lbs [16kg] Max Panel Weight Each 1-1/8" [29mm] to 1-3/8" [35mm] Panel Thickness Tap In Pivot/Guide Type Residential Grade Bi-Fold Door Hardware 1601 "Full Access" Bi-Fold Door Hardware 30lbs [14kg] Max Panel Weight Each* Residential Grade Full Access Bi-fold Hardware *Heavier Panels Possible With Optional HingesFREE SHIPPING ON QUALIFYING ORDERS $49 OR MORE Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted. Prepare to Install Bi-fold Doors Remove the old doors and hardware. Then measure the closet opening.
Use this to check the size recommendations when buying new doors. Good to KnowFor smaller openings, consider using a single bi-fold door. Repair the door opening as needed, such as filling old screw holes and painting. To help position the new doors in the opening, lightly mark the centers of the closet. Use a level to mark plumb lines on the sides of the jambs. Install the Track and Brackets Bi-fold doors work with a track and brackets. Cut the track to leave a 1/16-inch gap on either end. Then install the track – centered on the top of the frame (header) – with the pivot bracket toward the jamb. Center the jamb bracket at the floor. Drill pilot holes and then fasten the bracket to the jamb with screws. Before installing the hardware, paint the doors. It's easiest to paint them on sawhorses. When the doors are dry, use a hammer to lightly tap the pivots into the holes at the top and bottom. Install the doors by inserting the top pivots into the brackets.
Then seat the bottom pivots. Insert the snugger guide (the plastic white round piece that's shown in the picture) into the track. Then squeeze the guide pivot on the top of the door, position it under the track, and release it, making sure the guide pivot is securely in the track. Check the door height. The doors shouldn’t rub on the floor or come in contact with the header jamb. To change the height, lift the door and rotate the bottom pivot. To make it plumb, lift the door and slide it into the desired position on the jamb bracket. Loosen the screw in the top pivot bracket and slide it until the door is plumb and then tighten. Some bi-fold doors include pulls, but you can also install decorative hardware to complement the other doors. To install decorative pulls, mark a comfortable height on the face of the guide door – centered is usually best for ease of use. Hold the hardware in place, marking the holes. Then secure the hardware. Aligners help keep the doors closed.
From inside the closet, loosely attach them on the back of the doors about 12 inches from the floor. Adjust in or out so the doors snap closed. Then tighten the screws. Make sure the doors are working properly and make adjustments if needed. Watch Our DIY Basic Videos What Is The Backset Of A Door?How Do I Drill A Pilot Hole?1700 Bi-Fold Door Hardware Smooth operating, non-binding top hung bi-fold hardware designed for use with solid core wood door panels. Available with either painted steel or extruded aluminum tracks. Surface mounted pivots and guides (no hole drilling). Four way adjustable bottom pivot bracket, shock absorbing hinges self locate and automatically align doors. 1700 Series Bi-Folding Door Hardware Select a hardware set part number with track length that accommodates your panel sizes. Don't see a hardware set that matches your exact panel size? Johnson track can be cut down to accommodate narrower panels by ordering the next longer track length hardware set for your panel widths and cutting the track down..
Bi-Folding Door Hardware Sets for standard panel/opening widths. Sets include all necessary hardware for 2 or 4 folding panel installations. Track available in mill finished aluminum or brown or white rolled steel. Track can be cut down to accommodate narrower panel/openings. Custom 1700 configurations possible by ordering 1700 components by the piece. 1700 Series Printed Instalation Instructions 1700 Finish Trim Guide Bottom Guide Track Application Guide Mortise Hinge Installation Guide 1700 Series Quick Reference Drawings Select a hardware set part that matches the number of doors to slide and track length to accommodate your door widths. Johnson track can be cut down to accommodate narrower panels by ordering the next longer track length hardware set for your panel widths and cutting the track down.Sets include all necessary hardware for 2 or 4 panel installations. 3/4" [19mm] to 1-3/4" [44mm] Oversized item must be shipped freight.