8 1×4, 8’ Long 2 1x2s, 8’ Length 3 1×3, 8’ Length 1 1/4” Finish Nails 18- 1×4 @ 31” Panel Boards 2 – 1×2 @ 49 1/2 “ Side Legs 2 – 1×3 @ 49 1/2” Front Legs 2 – 1×3 @ 38 1/2” Back Supports 2 – 1×4 @ 38 1/2” Front Trim 1 – 1×4 @ 26” Center Trim 1 – 1×3 @ 44” Top Trim 1 – 1×4 @ 45” Top Trim 2 – 1×4 @ 30” Ends cut at 30 degrees off square, parallel, see last step Start by lining all the 1×4 panel boards up, rotating the grain so the bark side is up, then down. Then if you have a nailer, glue and nail the top and bottom trim in place. Otherwise, screw from the back to hide your screw holes. Shown above back side up, so you would just screw through the trim into the back side of the panel boards. Now screw the legs on with glue and 2″ screws. Nailer would be handy here, but if you don’t have one, you can screw the leg fronts to the legs. Use glue and 2″ screws or nails.
I highly recommend measuring and cutting these to fit. Nails would hide best, and even if you don’t have a nailer, if you plan to stain, I suggest using a hammer and finish nails to hide any holes. If you plan to paint, go ahead with the screws and glue. Mark the center and use 1 1/4″ fasteners and glue to attach. Now add the top trim with screws or nails and glue. Center on the top. Use finish nails and glue to attach the top to the top trim. Start by cutting 2 1x4s 36 3/4″ long, with both ends cut at 45 degrees off square, parallel to each other. Then on the top end, measure in 2″ and mark a line square with the top edge (see above diagram). Attach the cross supports to the headboard with 1 1/4″ finish nails and glue, nailing into all of the panel boards.These are the care and use instructions we sent to customers when we were selling memory foam products (we don't currently carry/sell any products, or recommend any other brands since we never tested any to feel comfortable recommending them).
People still read this page a fair amount, so perhaps these care and use instructions are to think of when unwrapping or using the brands of memory foam pillows, toppers, or mattresses you are buying from other sellers. Here are the manufacturer's instructions on opening your memory foam products and care and use instructions as well. Unpacking Your Memory Foam Product This Memory Foam Mattress Pad is made of the highest quality Visco Elastic Foam available. It has been folded, machine rolled and compressed for efficient delivery. affect its performance, but it may require 24 to 72 hours to regain its full shape. IMPORTANT Do not use scissors or any sharp object when removing the plastic cover. Exercise care and remove the plastic cover by hand. Gently pull the compressed product toIf you notice a slight odor when the package is opened, it is normal for "fresh foam" and will fade away inGently separate the layers by using a slow,
steady, uniform pulling motion. Caution must be exercised, to avoid tearing the foam. Once unrolled, allow it to recover naturally before making up your bed. Memory Foam Topper directly on top of the mattress and cover both with the same fitted sheet. If you have an overstuffed or pillow top mattress, you may require deep pocket sheets to cover the Memory Foam Mattress Pad. Cleaning: Simply spot wash by hand with warm water and mildRinse and gently wring out. air dry prior to use. Do not machine wash or dry. Safety - Fire safety precautions should always be followed. You may use an electric blanket, but be sure it is in good working condition and UL approved with no visible wear or My Hints for Airing out the Topper Pads We tend to air our out new Topper Pads out in a spare room with the windows open for fresh air. One trick we have learned is that the Topper Pad seems to air out more quickly with a fan
So we put the pad over a chair with the fan blowing on it, and turn the pad over in the morning to air out both sides equally. This takes care of the odor, for the most part, within a day or two and then it should be ready to go on your bed. After you begin to use the Topper Pad, you can take care of any residual odor by airing it out in the same manner during the day and then putting the pad back on your bed at night. In our experience, this takes care of any such residual odor in a few days. Another option is airing the Topper Pad outside for a day or two. Many customers tell us this works well, but of course you need to be careful about any dirt or moisture outside that may damage the Topper Pad. Using an appropriate foundation is important. be firm and supportive. Many people are able to reuse their current foundation if it is still firm and supportive. If you are buying a new foundation, you may want to consider buying one from a local retailer, or online
the Easy Fit or Easy Sleep are options, and you can find other more expensive slatted options if you search. One thing to be aware of is that the mattress needs good ventilation. So we don't recommend using the mattress on a solid wood platform unless it has a slatted top or holes in it to allow the mattress to breath. If it doesn't have good ventilation, moisture may accumulate on the bottom leading to mold or other issues. Similarly, we don't recommend using plywood over a foundation or box springs to firm it up unless you are willing to put in a lot of air holes in it (our suggestion is the holes be quarter sized and about 6 inches apart -- especially under the areas you tend to sleep Moisture build up that leads to this kind of mold issue isn't covered by the warranty since it is due to an inappropriate foundation and not due to any issue or defect in the mattress (if the foundation doesn't allow proper ventilation, this kind of problem could occur in