barn door pulley hardware

barn door pulley hardware

barn door mount calculator

Barn Door Pulley Hardware

CLICK HERE TO CONTINUE




2 - 2x10 @ 8 feet long 2 - 1x8 @ 8 feet long 2 - 1x10 @ 8 feet long 1 sheet of 1/4" thick plywood or hardboard (for back) 3 - 1x2 @ 8 feet long 4 - 1x4 @ 8 feet long 6 - 2x3 @ 8 feet long 2 - project panel pieces 17-1/4" x 36" (may be advertised as 18" wide project panel - measure in store) Hardware for sliding doors Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. 4 - 2x3 @ 84" 4 - 2x3 @ 17" 4 - 2x3 @ 14" 2 - 3/4" thick project panels or plywood 36" x 17-1/4"




5 - 1x4 @ 36" 8 - 1x4 @ 17-3/4" 2 - 1x8 @ 87" 2 - 1x10 @ 87" Middle Shelf Supports and Cleats 5 - 1x2 @ 14" 5 - 1x2 @ 17" 1/4" plywood pieces 36" long 1 - 1x2 @ 90" - both ends cut at 45 degrees, NOT parallel, longest point measurement 2 - 1x2 @ 18-3/4" - one end cut at 45 degrees, longest point measurement 2 - 2x10 @ 91" Doors are cut to fit, overall 20" x 30" Build two frames out of 2x3s.  The frames should be screwed together as this is the main support for the entire piece.  Use 2-1/2" or longer screws, or for those of you with a Kreg Jig, use 1-1/2" pocket holes and 2-1/2" pocket hole screws.  Don't forget to glue the joints. Don't be concrened about being perfect here, the entire frame is concealed. For the sides, add the side panels.  This plan is designed to work with project panels 17-1/4" wide.  You can use any material here, plywood or reclaimed wood too.  I recommend screwing these to the frames, but you could also use nails and glue - nails should be at least 1-1/4" long.  




I love how the back overhangs by 1/4" to conceal the back (will put that on in later steps). Now the face frame.  With the projec ton it's back, lay out all the face frame boards and glue and nail down.  Nails should be at least 1-1/4" long. Pocket hole users could also build the face frame seperately and attach. Lay the bottom shelf boards down on the bottom frame.  Nail and glue down, with nails longer than 1-1/4".  There can be a gap between the boards, but the shelf should not go past the back of the bottom frame (sides overhang by 1/4" to allow for the back). These guys are for supporting the weight of the middle shelf.  Nikki felt they weren't as necessary in a shorter span but for a longer shelf span, it's a good idea to have them.  Plus, it also makes construction easier.  Nail and glue down with 1-1/4" nails. You can also add two more at the back of the sides if you want. Build your bottom shelf by attaching bottom shelf boards to the shelf cleats.  




Use 1-1/4" long nails and glue to attach.  Can have a gap in the middle. Place shelf inside console and attach from outsides to secure in place. To get the planked look on the back of the console, Nikki ripped 1/4" plywood into strips and then attached the individual strips to the back.  You can also use full sheet of 1/4" plywood. You can use shorter nails here but if you don't want to buy a shorter nail (3/4" would be ideal) the 1-1/4" nails would be fine. The bottom is trimmed out in simple 1x2s, mitered around corners.  Use 1-1/4" nails and glue to secure. Attach top with the longer screws you used to build the top frames (2-1/2" or longer) so top is flush to back and side overhangs are even.  TIP: You may wish to stain the top boards first. Nikki built the doors shown with 1/2" plywood with smaller strips nailed on top, but you can use a variety of different methods to build the doors (love the reclaimed wood!) Nikki makes her own sliding door hardware too.




Jaime from That's My Letter provides a good tutorial on her sliding door hardware if you want to check that out. Console Table Plans, Buffet, Sideboard and Credenza Plans, Cabinet Plans, Media and Entertainment CentersBedroom, dining room, entry way, living roomHome Barn Door Roller Hardware Kit, 450 Lb. Capacity Barn Door Roller Hardware Kit, 450 Lb. Capacity Be the first to review this product $36.99 PK This barn door roller hardware kit is zinc plated and has a 450 pound capacity. The durable roller hardware is manufactured by Western™ Products of Indiana putting you on the right track. This hardware kit includes two barn door rollers, hangers, and attachment brackets. Description More Information Reviews (0) Roller door hardware is no longer just used for the barn. This hardware is constructed of steel and is zinc plated, making this product durable enough for your barn yet pretty enough to use in your home. Each kit includes two door hangers, which are recommended for each door.




The door hangers are corrosion resistant, with low-friction and low wear, allowing your barn doors to open and move more smoothly. This roller door hardware kit includes two single brackets and one single splice bracket to mount plain rail on the wall. The door roller track is sold separately.SpecificationsPart # N112-128450 lb. capacitySteel with zinc platingDelrin® bearings2 single mounting brackets1 spliced mounting bracket includedDoor roller track sold separatelyComplete your rolling door kit with a 6 ft. door track, ASC #21103, an 8 ft. door track, ASC #21104, a 10 ft. door track, ASC #21105, or a 12 ft. door track, ASC #21106, as well as roller stays, ASC #20411 and 20414, and a sliding door latch, ASC #20415.For additional products, check out our sliding door parts selection.Also, you can view or download the Barn door accessories brochure. 32 LB. HANGER KIT (2/PK) in Sliding Door Parts and at Agri Supply ®. Shipping & Return Information Review Summary Overall Rating: None Be the first to review this product Customer Reviews No Reviews May We Suggest Galvanized Door Track, 6 Ft. Heavy Stay Roller SLIDING DOOR LATCH

Report Page