Why We Why We Fiat 500 Replacement Key Cost (And You Should Also!)
Fiat 500 Replacement Key Fob
If your remote key fob isn't working, it might be time to replace the battery. If you replace the battery but it doesn't work, the problem may be somewhere else.
At United G28CarKeys , we specialize in the creation of new keys for classic automobiles. We have all the necessary tools and parts for this service.
Dead Coin Battery
A dead battery is the most frequent reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob is equipped with a coin cell battery which will quickly drain in the event that it is not used often enough. If your remote has started to show signs of loss in range or stopped functioning or not responding, then the battery could be dead.
Metal clips hold the battery in place on the key fob. If the clips aren't secure, it could lead to contact issues that will stop the remote from receiving power. Use a flathead screwdriver to break open the retaining clip and then remove the old battery. Be sure to use an alternative battery that has the same type of voltage, size, and specification as the original battery.
The key fob could be damaged or corroded due to exposure to water. Even a small bath in soapy water could harm the electronic chip in. Keep your key fob dry.
Water Damage
If your key fob isn't working properly, it may be caused by water damage. The rubber seals on key fobs stop them from getting damaged by a small drizzle or splash of water. However, it is crucial to keep the keys from the washing machine, ocean, and even the pool.
The key fob is equipped with an electronic chip inside that sends a signal car's immobilizer system. The chip is what allows the 500 to be locked and started. If it gets wet it will cease to work.
You can clean the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to determine whether they're still working. It is recommended to replace the key fob when it is submerged in salt water rather than attempting to repair it yourself.
While a replacement fob could cost you a little bit of money, it's a lot cheaper than paying for your Fiat 500 to be towed to the dealership and repaired! You can also make it yourself with just a few steps. Make sure you have the correct battery type before you attempt to open your key fob. This task is much simpler than it appears and you can find step-by-step instructions online for virtually any key fob in your car.
Faulty Chip
The chip located within the key fob communicates with your vehicle's immobiliser to ensure that your car is only able to start when the correct key is used. If the chip is damaged or destroyed, your car won't start no matter what you do.
A faulty chip can occur due to several reasons, but the most common cause is water damage or a dead battery. It is best to hand over the repair to a professional locksmith who can repair the chip quickly and at an affordable cost.
If your key fob does not function after exposure to clean tap or rain water take it off the battery. Wipe down the electronic component with a towel. If the key fob will not function, there is the possibility that it has an issue with the component and requires to be replaced.
Some people will visit their dealer in order to get a new Fiat fob. However, this could be costly. United Locksmith is the best place to go if you need your Fiat key fob repaired at a reasonable cost. We have the tools and knowledge needed to repair your Fiat key fob in a timely and professional manner.
Faulty Receiver Module
Fiat key fobs send signals up 50 feet away to the vehicle, which allows it to unlock and close the doors (and start the vehicle if it has automatic transmissions). However there are several things that can cause the fob to cease working. This includes a dead coin battery, water damage buttons, worn out buttons as well as a receiver module problem or signal interference, or an electronic chip malfunctioning.
If the fob was in an area that has experienced extreme trauma (such as being dropped onto the hard floor or washed in the washer) the fob may not be in a position to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that can only accept a signal from a genuine original key, and not from any other.
If this is the case, then you will require replacing your fob. A professional locksmith is able to handle all aspects of the key replacement process and can even program a brand new one for your 500. They can even provide an clone fob that performs just like the original (and costs just a fraction of the cost).