Why Incorporating A Word Or Phrase Into Your Life Will Make All The Change
How to Replace a Kia Sportage Replacement Key
The key of many Kia models comes with an entry system that is keyless in. This key usually resembles an electronic remote and can be changed by a new one purchased from a Kia dealer or a locksmith.
Key fobs might stop working for a variety of reasons, such as the battery of the coin is dead worn buttons signal interference, water damage, and a defective receiver module. Here are some tips on how you can get your Kia Sportage replacement key to function again.
How to replace a smartkey or remote key?
It doesn't matter if your Kia is equipped with an intelligent key, remote key push to start key, or regular metal non-transponder key the battery in these keys will eventually need replacing. This is especially relevant if your vehicle shows a message that states the smart or remote keys have low battery power.
It's a fairly simple procedure. To replace the battery in the keyfob remove your mechanical key from the slit at the back of the fob. Then, pull the cover open. Inside the key fob will be an incredibly small screw that holds the battery in the correct position. Remove the old battery by detaching the screw with a small screwdriver. Then, insert the new and close the slit on the key fob.
Test the key fob by pressing the lock/unlock buttons. It's good If the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you have to go on errands around Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a programing machine that is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of steel) do not require programming. If you want to change the programming of your key, you'll have to write down the key code's number on the tag for the key code.
How to replace a battery
If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A weak battery could cause other issues, like the check engine light appearing or the engine not running properly. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires just some basic tools.
Before you begin the process ensure that your vehicle is off and that all doors are shut. Find the small metal or a plastic piece that is located at the bottom of the key fob. Jiggle it until the key comes out. The key can be inserted into the driver door handle to unlock your car.
To replace the battery inside the key fob remove the rear cover. Use a plastic pry tool to remove the latch that holds the black negative cable. Take the old battery out, and then position the new battery to ensure that its "+" side faces you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts on the metal.
After the new battery has been installed then turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia's keys fob once more to ensure it's functioning properly.
How to replace the smart key?
Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between them is that the smart key comes with an incredibly small key blade that is hidden inside, while the standard fob does not. Both key fobs have an internal battery that will eventually require replacing. It is a simple process that takes just two minutes.
Before you begin before you begin, ensure that you're on a level surface with adequate lighting and that your Kia is off. Also, remember that there are tiny components inside the fob that could be snagged if not cautious.
The release button for the small size is located on the lower backside. It will be either a circular silver button or a rectangular slot. Once you press this button, the mechanical blade will come out and you will be able to open the key fob.
After the key fob has been open, remove the battery. The Key Lab is CR-2032, and can be bought online or in your local auto parts shop. Once you're done, your key fob should allow you to lock or unlock and start your vehicle, even if it isn't running.
How do you replace a mechanical key
The Kia keyfob is an excellent convenience that allows us to lock or unlock our car by pressing the button. Like any other device there are issues with it occasionally. There are solutions to solve these issues and keep your key fobs functioning for many years.
One of the most common problems is a low or dead battery. This can cause the fob to stop working completely or to work intermittently. If this is the case you should replace the battery a new one.
If this doesn't fix the issue, try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage internal components, or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.
Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the fob to make sure it's functioning correctly. Contact a dealer locksmith to address the issue in the event that the key fob is not working. Make sure they cut you an emergency key that functions for all door and trunk cylinders to prevent lockouts in the future.