Who's The World's Top Expert On Replacing Lock On Upvc Door?
Replacing Lock on uPVC Door
To replace the lock, you must first remove the handle and screw holes. This is usually simple to do.
The next step is to find the screw that holds the barrel in place. This screw is usually different in colour from the screws that are used in other locks, and is located on the edges of the faceplate of the lock.
Remove the Cylinder
To change the lock on your doors made of upvc first, you must take off the cylinder that is currently in use. This is a simple process that takes around 30 minutes. All you require is an ordinary screwdriver. You'll need to locate the Euro cylinder fixing screw that is typically located in the edging on the inside of the door, just next to the lock cylinder. The screw is usually different in color from the other screws and will be easy to find. Take it off and store it in a safe location.
After you have removed the cylinder, you can then begin removing the handle. To accomplish this, you'll have to open the door wide enough so that you can see the inside edge of the door and the faceplate on the outside of the lock.
Start with a screwdriver to remove the screw that connects the handle to the door. Once this is removed, you should be in a position to pull the handle toward you and the rest of the mechanism out of the door.
If you're having difficulty getting the handle off then you'll need to remove the screw that holds it to the stud inside the door frame. This can be accomplished with a drill or screwdriver, and you'll need be careful not to cut the screw head or cross-thread it.
When you're ready for replacing the cylinder, be sure it is the right size for the door you have. Cylinders are measured using two factors: (a), the distance from the center of the Fixing Screw to the bottom of the cylinder and (b), the distance between the keyhole's hole the keyhole and edge of the lockplate.
Take the handle off
If your door handle made of upvc becomes stiff or loose The good news is that this is a fairly easy problem to repair. The multipoint lock cylinder or other internal parts inside the door, between the handle and frame, are usually the culprits. It is not uncommon for Upvc locks to get worn due to the weather, heavy usage or simply aging. This will often lead to problems with the locking or closing mechanism of the door.
The cylinder may wear out and make it difficult to turn the key. The lock may also become stiff causing the handle to droop. This can be fixed by replacing the cylinder which is an easy procedure. It is possible to complete this yourself, although some knowledge of how the mechanism works is required. You'll need to take off the handle in order to replace the cylinder.
To do this, you'll require a screwdriver as well as a tape measure. It is important to know the exact size of your cylinder, so that you can get a replacement cylinder that is suitable for. The cylinder is the element that locks your door made of upvc, and it is essential to ensure that you receive a replacement of the same size.
To remove the old cylinder you must remove all screws that hold it. Be careful not to remove the screws, as this could make it difficult to remove the screws in the future. After the screws have been removed, the cylinder should be able to be removed easily.
Take out the Lock Barrel
Upvc is a strong material and designed to ensure your family and you are secure. They are available in a wide range of styles and colors that can suit any style of home. These doors are also energy efficient and maintenance-free. They are not without drawbacks. As time passes, the barrel or locking point lock can become faulty and will require replacement. This is a simple process however there are some things to know prior to beginning.
You'll need to take off the door handle in order to get access to the screw that holds the lock cylinder. The screw is usually different from the other screws and can be located near the keyhole at the outside of your door. Remove the screw and place it in a safe location. Then, carefully slide out the inside and outside door handles. Make sure to do this slowly and not too fast as it can cause damage to your uPVC door.
After you have removed the handles, you can use a screwdriver to take out the screws that secure the handles to the door frame. This will allow you to gain access to the pins holding the cylinder in place. You can then try to wiggle and tug the cylinder in order to see if this can loosen it. Once it comes loose, pull it towards you, then pull it away from the socket.
After taking out the old lock cylinder it is crucial to replace it with a brand new one that is anti-snap and anti-bump. You can do this yourself if you have the tools you need, or you can engage an expert locksmith to do it for you. This is a relatively easy task that will take about five minutes to complete.
Install the New Cylinder
A upvc door lock can be damaged or broken in many ways, for instance, a tenant might have moved out but not returned the key or the cylinder might have become damaged and no longer works as it should. It is crucial to select the correct size replacement for your upvc door lock. If the wrong one is installed, your doors could be more vulnerable to the 'lock snapping technique which is the reason for 25 percent of burglaries.
To prevent this from happening it is vital that the correct cylinder is installed and the procedure to do it is a breeze and takes just five minutes. To swap the handle faceplate and the cylinder, you will need to take off the screws that are attached to them.
Make sure that you open the handle and have access to the lock cylinder on the side of the faceplate of the handle. This will allow you to easily remove the lock cylinder from the handle without the need to move it, and expose the inside of the frame.
Next, remove the old cylindrical device and take a measurement of it. It is important to know its overall length and the measurement of the cylinder that moves to lock or open the door. This will help you find a replacement of similar in size or smaller. This is the most crucial aspect of the entire procedure. A cylinder must be flush with the handle backplate and be no more than 5mm protruding from it.
Install the Handle
It is not uncommon for a door lock made of upvc to stop working and this could be caused by a broken part inside the case that controls the bolts that retract into the keep or strike plate. This can often be resolved by adjusting the Allan key underneath the hinges. However, this can occasionally cause excessive stress on the parts within the central casing, and it is recommended to call in a professional.
When changing the handle, it is important to have easy and quick access to both sides of the handle, as well as having the right tools. repair window locks upvc is also a good idea to prop the door open so that it doesn't shut during this process.
The first step is to loosen the screws holding the handle in position with the help of a screwdriver. Once these screws are loose the handle can be removed. After taking off the cylinder and the handle, it's time to install the replacement handle. Make sure that the new handle fits your existing central cylinder and the cylinder. To determine the right size take a measurement of the spindle's length on the lever that you currently own. Verify that the screw fix centre on the handle is identical to the screw fix centre on your current hole centre or cylinder.
Replacement handles from Fab and Fixed come in different styles and are built to last. These handles are perfect for those looking to upgrade their upvc handle and improve home security. Having the right handle will ensure that your home is secure and safe and won't be easy for burglars to break into.