What Is Saab 9-3 Key Replacement And Why Is Everyone Speakin' About It?
How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a distinct set of steps to take to add another key. It requires dealer service with a handheld computer dubbed Tech-2. Then the transponder must be replaced and a key are required to be purchased.
It is an excellent idea to rotate your keys so that one does not get worn out more quickly than the other. This will also keep your keys in good condition.
Replacement Case
As opposed to the traditional Saab keys of old keys, the new key fobs contain electronics which makes it hard to make a copy. This has made car theft much more difficult than it was twenty years ago. It also makes it more costly to replace keys that were lost.
Saab 9-3 owners must have two keys that work. If one is lost, it costs a fortune to get another one for the car because it involves replacing the CIM module and reprogramming the locking cylinders. Dealers charge between $100-$200 for this.
There are ways to reduce these costly costs. Some parts providers will use the code of a spare key to cut a brand new metal blade for less than that of a dealer. The key must be the exact same as the original in order for it to function in your vehicle.
Follow these steps to replace the case. You'll need a flathead and a lot of patience. Utilizing the screwdriver, slowly pry the plastic apart and separate the emergency keys from the case. Once you have the case open, remove the electronics and put them in your new case. Make sure to insert the correct key and badge back into the case as well.
Replacement Battery
The replacement battery for the Saab 9-3 is an inexpensive component that can be replaced easily and quickly. This YouTube video from Cyclone Cyd demonstrates how to replace the battery of the remote fob with only four steps. This tutorial is compatible with any modern Saab key fob. However, the process might differ slightly.
The first step is to find the button that lets off the backup key inside the fob. It's usually just below the Saab logo on the back of the fob. Then take a flathead screwdriver to insert into the small hole of this button. This should be sufficient to allow you to open the fob case to allow you to change the battery.
After the new battery CR1632 is installed, you can reassemble the remote key fob and program it to your car. The entire process shouldn't be more than an hour. It is a very simple process that does not require any special equipment.
The process is a bit more complicated in the event that you lose your key, but it's possible. saab car keys will need to read the car's VIN and then purchase a replacement key blade and a TWICE module with the correct unique code. The dealer will then need to program the key using MDI, a new software tool.
Replacement Key Fob
The key fob is a device that locks and unlocks your car, it has an internal battery. The batteries have a lifespan and eventually go out of service. This is a typical issue that occurs with all vehicles, and the good news is that you can change the batteries in a majority of key fobs without replacing the whole case. Amazon sells fobs for replacement that already have all the electronic components installed. It is easy to remove the case and replace the batteries. It is important to keep in mind that you'll need remove the emergency key first, and you can accomplish this by inserting an incredibly small screwdriver with a flat head into the slot in the middle of the case. Work the screwdriver around the case until it is split open, making it easier to take it out.
When you're ready to replace the keys, make sure you have spare keys, because this can cut down your total cost by a substantial amount. If you have an additional key, you can request the dealer to cut it in half and program it to your car. This is a lot less expensive than purchasing a new fob.
If you do not have a spare key one, you can add another key to your car, however this requires a lot of research and effort. It can cost a few hundred bucks to add an additional car key. The computer of the vehicle also has to be programmed. This can be accomplished by a professional, however it is an expensive option for the majority of owners.
Replacement Ignition
Contrary to the earlier Saab automobiles, the new SAAB 9-3 models feature an extremely sophisticated alarm system that is based on a coded key. This means that if you lose your only working key, replacing it with another key can be extremely expensive as the car has to have a specific computer module installed, and it also needs to be specifically programmed to accept a new key. The majority of locksmiths aren't able to do this, and even dealers can charge several hundred dollars just to program the new key!
If you've lost the only working key and a dealer is able to replace your car's computer (known as the CIM or SAAB TWICE) to make a replacement, and will charge top dollar for it. We can reprogram the EEPROM in your car computer so that it is prepared for a new key. This will save you more than 50% off the price you'd have to pay an auto dealer.
If you've owned a SAAB 9-3 for a long time, you know that the ignition keys are not very durable. They can be extremely sticky, and the buttons are known to be ripped off occasionally, so you should consider replacing your ignition key if it isn't working as it should. It's not as difficult as it appears to replace the ignition key. With the right tools, it can be done quickly.