This Is A Guide To Peugeot Keys In 2023
Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths who have the proper tools and know-how. They can create and program keys more quickly and at a lower cost than dealers.
If the key fob stopped locking or unlocking your doors it could be due to a dead battery in the coin. There are many other reasons for the key to be malfunctioning.
Dead Coin Battery
A dead coin battery can stop your Peugeot 208 from locking or unlocking and will not start the engine. In this scenario you'll need to employ the alternate method of starting as described in your vehicle's owner's manual.
The spark plugs might also be worn out. Spark plugs are what ignite the fuel to start the engine. They are only able to last for a short time. If they aren't utilized enough, they will eventually fail.
There is a simple solution for this issue. Check the voltage of the battery with a multimeter. If it is below 11.5 Volts and you are not satisfied, then it is time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by removing the rubber cover from the two terminals of the battery, and then using a wirebrush to remove any corroded battery parts. Then, reconnect the cables to the positive and negative poles.
If your 208 will not start and the battery hasn't failed, you should inspect the spark plugs. You may find that they're dirty and they don't spark. The spark plugs can be cleaned in an workshop.
Peugeot cars are equipped with a transponder key that works with the car's ignition system. This makes sure that only the correct key is able to start the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle.
Water damage is a frequent reason for this issue. This is a common issue in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, you should call a reputable auto locksmith who has all the tools and equipment required to change the key's programming. They also have the latest technology and equipment needed to make the Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.
Faulty battery contacts
Peugeot changed from the old carbon-encased transponder chips to a new type of chip that incorporates electronic components within circuit boards. This new system works well when it's brand new, but as time passes, the circuit boards begin to deteriorate and stop working correctly.
This could prevent the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this happens, it's a good idea get in touch with a Peugeot specialist or locksmith.
Another common issue is when the battery for the key fob begins to fail, which causes the key blade to stop from entering the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a quick fix.
Faulty Receiver Module
If your Peugeot key fob was not working after dropping it on the floor, getting exposed to a sudden rain or accidentally washing it may be due to a faulty receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which regulates the central locking system of your Peugeot vehicle.
The key fob itself is fitted with rubber seals which prevent water from reaching the electronic chip inside. The chip can be damaged by water if it is exposed to the water for an extended period of time. The high salt content in the pool or ocean waters can cause damage to the key fob if it is submerged.
The module will need to be replaced if the Peugeot spare key is no longer working. This can only by done by a Peugeot specialist or a professional auto locksmith. As opposed to other cars, Peugeot keys are protected by a unique immobilizer system that requires the right coding to begin the engine. This is why you should only go with a knowledgeable Peugeot locksmith for the job of programming and creating an alternative.
Computer on-board is not working properly
The computer on the board of your Peugeot is responsible for a number of the systems in the car, from power windows to airbags. If something is wrong with these systems, it'll typically display a code that identifies the problem. The code will be stored within the system until the issue is resolved. Most often, this involves replacing the onboard computer.
The most frequent cause for the warning light of the airbag to illuminate is corrosion or loose connections in the sensor. It can be due to wear and tear, aging, or exposure to moisture and salt. It is imperative to have this issue addressed as quickly as you can, since a malfunctioning airbag can be risky in the event of an accident.
If you encounter a card not found error on your Peugeot key fob, the battery in the key fob could be dead or weak. This will stop the key fob sending a signal that will disable the immobilizer on your vehicle. Try this by pressing the unlock button on the key fob and then trying to start your vehicle. If this doesn't work the battery on the key has to be replaced.