The Reasons To Focus On The Improvement Of Upvc Window Replacement Hinges
Choosing Upvc Window Replacement Hinges
It's not as difficult as it might appear to choose and install upvc replacement hinges. Make sure that the arrows on the hinges face in the correct direction, and then measure the thickness of the hinge arms on the frame opening (13mm or17mm).
There are many different types of hinges to choose from, each one with distinctive features. This article will review the most popular uPVC hinges, as well as their benefits.
Egress/Easy Clean Hinge
They are a great option for replacing or upgrading the fire escape safety window since they can be opened at a 90-degree angle. They can be disengaged to a 'easy-clean' position, allowing you to access the outside of windows without having to climb ladders or lean at risky angles.
These heavy duty egress hinges are made by Yale which is among the most popular and respected home security brands on the market today. They are suitable for all types of uPVC side-hung windows. By pressing a tiny button, the window sash is slid to the side and into the easy-cleaning position. When the sash is closed, it will automatically reset to its initial position.
They are available in 13mm and 17mm stack heights. Based on the size of your window we recommend using our Egress Selection Guide to determine which product is best for you.
These hinges can be used with conventional side-hung frames made of aluminum or uPVC. The friction screw is used to adjust the resistance. This makes opening the window more simple and reduces the chance of accidental closing during strong winds. They have been cycle tested to over 30000 cycles and comply with BBA/Secured by Design and British Standards approved BS EN 13126-6:2008.
The Nico Egress Easy Clean friction hinge is simple to use and does not have buttons or catches. It provides a convenient and secure solution to emergency exit and cleaning. Firstly, open the window to the egress (full opening) position and then press the hinge retaining clip located on the inner side of the bottom corner. This will release both the bottom and top catches allowing you slide the sash to the clean position. Close the window once you have the sash in an easy-cleaning position. This will reset the hinges to their exit positions.
Fire-Escape Hinge
Fire Escape Hinges commonly referred to as "Easy Clean" hinges are used to replace side opening windows for egress (fire safety) reasons. These hinges permit a larger opening in the event of a fire. The building regulations state that this type of hinge must be installed in any habitable space with windows.
They feature an exclusive friction stay that allows the window to be opened to 90 degrees and also allows the opening sash to slide across the glass when it is open to allow easy cleaning of the exterior side of the glass without having to climb ladders. The hinges are simple to operate and don't have complicated buttons or catch mechanisms. They can be operated from inside of the home using a safe, simple lever.
The hinges are manufactured in the UK by Cotswold and come complete with a child safety limiter for use throughout the day which can be turned off with a hidden button giving you peace of thought that your children won't accidentally open the window too far. They are available in 13mm or 17mm stack heights.
Take a measurement of the length of the existing side-hung window hinge that is attached to the frame. (See the guide on measuring the size of Upvc window hinges). Choose the proper size hinge from the list below.
Note that this measurement is taken from the hinge's point that connects to the frame, not the sash. The actual hinge length may be shorter or longer depending on the way your windows were made in the past. When deciding on the width of the hinge most upvc frames will fit a stack height of 13mm, but if your old window frame has 17mm, you should select this option. You can also use the 4mm packer in order to make up the difference. All the hinges are supplied with two hands (1 left and 1 right). The hinges are not equipped with screws. They can be purchased separately if you require. We recommend using our upvc window hinge repair screws. These are specially made to improve the performance of your hinges, allowing them to operate efficiently for a longer. They have a lower friction design and a better weather seal, with a brand new nylon reducer end cap.
Restricted Hinge
There are occasions when windows must completely open, and this can be difficult using hinges that are standard. These child safety friction hinges are a great solution to this issue. They can be used in situations where ventilation is required but cleaning or escape from an fire isn't feasible. They restrict the amount of opening the sash, and allow for the bypass of this restriction by pressing a button. They are available in 13mm or 17mm stack heights. They can be used to open both side and top hung windows.
The Nico Restricted Egress Friction Hinges combine the advantages of a standard restrictor and an escape pivot to provide a simple and efficient way to meet building regulations. It is available in 13mm and 17mm stack heights and is suitable for both side and top opening uPVC window. It is available in two parts that has one hinge which is the restricted egress, and the other the unrestricted. This lets one hinge be placed at the bottom, while the other hinge is placed at the top.
repair window hinges have been tested to BS6375 Part 2. They are intended to be used on windows that isn't able to be fully opened, like a small children's bedroom. The mechanism restricts the distance the sash opens to an appropriate height of 100mm, and re-engages once the window is shut.
These uPVC friction-type hinges can be used with any type of windows. They are particularly suitable for windows that are hard to reach, like those in three-storey houses or ones that require the use of a ladder. They can be upgraded with our range security enhancements, like hinge guards, or dog bolts to attain PAS 24 performance.
When replacing a hinge on a window, it is crucial to measure the length of the existing hinge to ensure that you purchase replacements that are similar in size. This can be accomplished by looking at the picture gallery of the hinge and then deciding where you want it positioned. The top-hung hinges can only be positioned on one side, whereas the side hung ones can only be put on one side.
Standard Hinge
Standard hinges feature metal-to-metal contacts and don't require extra parts to reduce friction. It is available in a variety of finishes and also comes with a fire rating. For a quick way to determine the radius of your hinge put it on its flat surface and then line up with a quarter and dime in two corners. If the dime fits better than the quarter, the corner is rounded by 1/4 inch; if the quarter fits better, it's rounded by 5/8 inch.
The hinge you choose can enhance or break the look of your door. It's important to match the style and finish of your door with the hinges to create a seamless look that's both practical and visually appealing.