The Most Significant Issue With Double Glazing Door Lock Repairs, And How You Can Fix It
Double Glazing Door Lock Repairs
Has your uPVC window or door mechanism deteriorated? Perhaps the door or window handles aren't aligned correctly or are difficult to use.
You'll be wasting energy when your double-glazed doors do not work properly. This increases the likelihood of burglaries. Owen the Locksmith can repair your door lock for an affordable cost.
Snapped Key
If a key is snapped off in a lock, it can be incredibly difficult. It could also be a security risk since the door may not lock and make you vulnerable to burglars. There are a few easy fixes you can try to resolve the issue and get your door working again.
The first step is to remain calm. If you get scared and start poking around wildly you may end up pushing the damaged piece of the key further into the lock, making the situation even more difficult.
Next, spray WD-40 or another penetrating oil into the lock to help the broken piece slip out more easily. You can also use the screwdriver to break any pieces stuck. If you're fortunate enough to have a little bit of the key left sticking out it, you can make use of a paperclip or other metal object that is thin to grab it and pull it out. Both methods work, but you must be careful not to push the broken key piece further into the keyway.
Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these, you can bend a hook with needle-nosed pliers. You can also use a pair of tweezers grab and pull out the last bit of the broken keys.
If you can't get the broken piece of the key out, try using a lock de-icer. This is usually available at most hardware stores. It is used to freeze any moisture or ice that may be in the lock.
If none of these solutions work, it could be time to consult a locksmith. Fitlocks specialists are able to quickly solve problems with uPVC door locks and mechanisms such as snapped keys and broken handles. They can also reconfigure the double glazing door mechanisms so that they are easier to operate. You can request a double-glazing repair online or contact us to discuss your needs.
Broken Cylinder
A broken cylinder is an extremely risky security issue. A professional locksmith is able to repair the cylinder. To fix the cylinder a locksmith will need to tap it. This can be done with a hammer, or any other tool. The best method is to employ a wire or long match. Then, put the end of the match or wire in the keyway. The locksmith will then strike the lock in order to crack it. This is better than using the hammer, which could harm the lock.
Overheating is the primary reason for cylinder heads to crack. This can occur when the cylinder block and cylinder head are made of various metals, like cast iron and aluminum. When different metals heat up and cool down at different rates, it could create hotspots locally that expand faster than the rest of the cylinder head, leading to cracks.
Another possible cause for cylinder cracks is corrosion. If the cylinder head as well as the cylinder block aren't properly maintained, it can result in corrosion or rust, which may cause them to expand at a greater rates than they ought to. This could lead to cracks in the future.
If your uPVC window or door lock is rigid and requires a lot of pressure to turn it could be due to a variety of causes. A faulty locking mechanism, misalignment or an old handle are the most common reasons for this issue.
Fortunately it is a simple and cost-effective fix for the majority of homeowners with double glazing. A professional locksmith should be able solve this issue within a matter of hours after arriving at your residence. Based on your requirements they will be able to replace the locking mechanism, replace the window handles, and change the gearboxes. A professional locksmith can always advise you on the most cost-effective solutions for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders which offer an additional layer of protection from burglars. It's a small amount to get the peace of mind that comes from knowing that your uPVC door is secured.
Broken Handle
It's not a surprise that window handle locks could break. They are equipped with complex mechanisms which deteriorate over time. It can be difficult to determine the cause of the broken window handle lock and fix it correctly.
If the issue is in the internal locking mechanism or the latch, fixing the broken handle will increase your uPVC double glazing door's security and help you stop drafts. It can be expensive to repair or replace the handle in a way that isn't done correctly. double glazing window repairs could also harm the frame and the lock of your door.
Screwdriver Open the window remove the screw that holds the handle. The screw should be located on the inside of the backplate, which is usually covered by an eye-catching cap to conceal it for aesthetic purposes. It is not recommended to lose any internal components of the handle like the plates and levers on either side. Keep them in the same arrangement to make it easier to replace them if needed.
Then, turn the handle until it's 90 degrees to the window frame. Finally, loosen the screw on the back of the handle that fixes it to the internal spindle with another screwdriver. Once the screw is free, you can remove the handle and take out the broken spindle. Replace it with a brand new spindle, ensuring it's the same length (you can find them online or at hardware stores). Screw it into the correct position. Be careful not to overtighten because this could damage the handle or the window frame.
Make sure the new handle is correctly installed Close the window and test the handle. Hopefully, it will work smoothly and you'll be able to unlock your window.
While you're working on the handle, don't forget to make sure your uPVC windows are shut properly. If they aren't closing properly, you may experience draughts or damp in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of the window frames to ensure they close properly.
Broken Spindle
It is quite common that the spindle in a handle breaks rather than the handle itself. This is especially frequent in uPVC tilt and turn windows. These windows require a handle that operates an locking device within the frame of the window. The handle is connected to a central rod that activates a series of locks that are shaped like mushrooms and secure into the frame of the window keep. If the dead latch mechanism is not able to open when the handle is turned, it is most likely the spindle is broken. This could be a frustrating issue.
Luckily, there are steps that can be taken to remedy this situation. A reputable locksmith can quickly and effectively fix this problem. A reputable locksmith will be able disassemble the handle of the window by using a tool that removes the wheel part that houses the spindle. This can be done without causing any damage to the handle or causing any other damage to the window frame.
After removing the wheel the technician can inspect the spindle and identify what caused it to break. This involves breaking the spindle into its constituent components and carefully observing their general condition, as in addition to any specific areas of damage or excessive wear. This procedure is typically performed by technicians in a clean and safe environment.
Then, clean the damaged spindle. This will help remove any dirt or debris which may be obstructing it from operating normally. Following this the spindle is cleaned, it could be repaired or replaced. If it is replaced, the technician can take an identical dowel size to the original and drill mating holes into both parts of the spindle. This will ensure that the spindle fits perfectly with the handle.
If the damaged spindle cannot be repaired, it might require replacement completely. Home centers offer generic replacements, but if the design of your window is unique then you will need to find a woodworker or cabinet maker who can make the exact component for you. After the spindle is installed, it can be fixed to the handle. Line up the screw holes on the handle with the screws already in the frame. Once the new handle is installed, you are now ready to operate your uPVC window.