The 10 Most Terrifying Things About Replacement Locks For Patio Doors
Replacement Locks For Patio Doors at Lowe's
Replacing your patio door lock is a simple way to improve the security of you home. However the correct installation and regular maintenance are essential.
In order to successfully replace the lock on your patio door it is crucial to know what kind of lock your existing one is. door locks replacement southampton repairmywindowsanddoors can identify the type by looking at the screw hole size and the face plate on the end.
Identifying Your Existing Lock
It is essential to know the differences between different types of locks before you decide to purchase new hardware for your lock. This will allow you to find the perfect replacement, and ensure that your home is safe and secure.
The most common type of lock is the cylinder lock also referred to as pin and tumbler locks. This type of lock uses combination of bottom pins springs, top pins and top pins to secure the keyhole and plug. Cylinder locks are available in different sizes. It is essential to determine the length and diameter of the cylinder you currently have before purchasing a new one.
To measure the width, loosen the screws that keep the cylinder in place and slowly pull it out. Then, take a measurement of the distance between the outside edge of the cylinder and its inner end and record the measurement in millimeters. Compare this measurement with the measurements of the lock you plan to purchase. This will ensure that the new lock will fit the door's lock hole.
Another way to determine the proper size of the lock you have is to test it by using keys. If the key slides easily into the cylinder it's the same width as the rekey kit you need. If the key isn't able to slide into the cylinder, it is likely that your cylinder is using a different keyways and cannot be rekeyed to accept that type of key.
It is always recommended to read the manufacturer's instructions included with a kit for rekeying, as each type of lock has its own unique set of installation requirements. It is also a good idea to to fully test the new lock after it has been installed to make sure that it works correctly and offers the highest level of security. It is also crucial to pay attention to any additional features your new lock might include in order to determine the ease of operate.
Measure the Width
A faulty patio door lock can result in serious security issues. It is crucial to examine your locks on a regular basis and replace them when necessary. This will ensure that they're operating properly and are safe. It may be a good idea to avoid problems such as a broken latch or keyway. Whether your existing locks are worn or damaged, you can get replacements at Lowe's which will offer the security your home needs.
Before you purchase a new patio door lock, it's essential to determine the dimensions of your existing one. This will give you an idea of what size to purchase and eliminate the risk of buying an unsuitable lock. There are two measurements you need to accomplish this: the backset and the depth of the case. The first is a distance between the edge of a lock's face and the centre of the hole that the handle spindle goes through. The second is looking at the depth of an lock from the outside.
It's also important to consider how you use your doors before deciding on the type of lock you need. For example, if your sliding doors open horizontally, you'll need to choose the top and bottom tab lock that connects to the strike plate, which prevents the door from being lifted or forced open. If your patio doors open vertically, you'll have to select a mortise lock with a spring-loaded hook latch which provides additional security.
It's important to note the location of the screw holes when determining the size of your lock. Certain mortise lock screws are round, while others are square. You'll need to know where the keyway is located. Some locks have a vertical keyway whereas others have a 45-degree angle. Take a picture of the lock with your digital camera to make sure you receive the proper replacement.
After you've gotten your measurements, it's now time to shop for the best patio door lock. Online, you can discover a wide selection of high-quality locks. Many branded products offer advanced security features that will ensure your home's security. It is essential to look at locks and read reviews prior to you purchase. Lastly, don't forget to regularly clean your locks to stop dirt and other debris from affecting the functioning of your doors.
Be sure to check the screw holes
Patio doors play an important part in protecting your home and should be checked for signs of wear and tear to make sure they're functioning correctly. Over time, your locks and spindle that connects the handles on the exterior and interior are likely to require replacement. A sturdy lock not only prevents unintentional entry, but it also increases security, energy efficiency and security.
There are many ways you can narrow your search for a new lock if you don't have the exact model. First, you must identify the type of keyway it uses. Rectangular mortise locks that are cutouts are usually used on aluminum patio doors, while E2126 and E2079 locks are set in a recess inside the frame of vinyl or wood patio doors. If you have an electronic camera, uploading a picture of the lock may aid in determining the type it is.
You can also determine the kind of lock by looking at the screw holes. Most sliding patio door locks have screw holes that align with the latch keeper that is mounted on the side jamb, but they are not always identical. Some screws may be longer than others, or have different threaded finishes. Some screws also have washers or a hex nut attached to them, which could affect the way they fit into the lock hasp.
If you are aware of the type of lock your home has, you can start preparing to replace it. You'll need to clean the lock first with a damp brush or cloth to get rid of any dirt that may hinder its operation. Once the lock is clean then you can apply a silicone-based grease to keep it smooth and quiet.
It's a great idea replace your old screws with longer ones. This will allow you to gain a better grip, and also install the lock with less effort. After you've completed that, it's a good idea test the handle and observe how the latch hasp engages in the lock.
If the hasp isn't engaging it, you may need to install an hex-nut or washer behind it to allow it to catch more of the lip of the door. You could also add a shim to the side of the lock keeper on the jamb to see if this helps.
Check the Lock Snib
The snib, also known as the lock mechanism, is situated inside the door handle. You can turn on and off the snib to open and close your patio doors. It is the first thing to look at when your locks don't work correctly. You should also examine the keepers located at the top and bottom door frames for any looseness or misalignment that could cause them to break. Make sure that your snib lock is correctly seated and that the lock hasn't been blocked or stuck in any other way.
The most popular patio door locks are mortise locks made of steel that secure sliding glass doors. Installed into the door frame, they come in many styles and are an effective security measure. Some are designed to hold keys while others feature an oval cutout, making it easy to lock and unlock.
A step-on lock with a thumb-screw is another popular option. It holds your sliding door in place without the need to turn the knob. These locks are typically found on older metal-framed patio doors, but they can be a great choice to secure wood or vinyl-framed sliding doors too.
When you examine your existing patio lock, note the type and size screw holes used to mount the escutcheon and the lock body. This will allow you to choose a lock that has the correct screw holes. It's also a good idea to inspect your strike plate to ensure that it's secured properly.
If you have Jason Windows boltlock sliding doors from 2000-2009, make sure the screws that hold the door are secure and not missing or loose. These screws keep the snib in a partially opened "vent" position to allow airflow, but also encourage security, and are important for preventing your lock from shearing. It's recommended for all locks to be inspected regularly and cleaned frequently to prevent debris, dirt or corrosion from obstructing the operation the lock.
If your snib is damaged, it may be possible to simply replace the entire strike plate and snib assembly. If your snib simply needs to be aligned it can be corrected by removing the strikeplate using a an abrasive blade and then backing off the adjustment screws (located between the screw). You will then be required to move the strikeplate up or down until the tongue of engagement is aligned with the Milgard logo.