Ten Ways To Build Your Peugeot Keys Empire
Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths with the right tools and know-how. They can program and create keys more quickly and at a lower cost than dealers.
A dead battery for your coin is most likely to be the cause if your key fob stops locking or unlocking doors. There are other reasons that the key might be malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking, and won't start the engine. In this case you'll need use the alternative starting method as described in your vehicle's owner's manual.
Another reason the 208 won't start is because the spark plugs have been worn down. The spark plugs ignite the fuel to start the engine. They have a limited life span. If they're not used enough they will eventually fail.
There is a straightforward solution to this issue. The best solution is to check the voltage of your car battery using a multimeter. If it's less than 11.5 volts, then you need to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by removing the rubber covers from the two battery terminals and then using a wirebrush to clean any corroded battery parts. Then, reconnect the positive pole cables to the negative.
Water Damage
If your 208 does not start and the battery hasn't failed, you should look at the spark plugs. You may find that they're dirty and don't spark. This can be fixed by cleaning the spark plugs in the workshop.
Peugeot automobiles are equipped with a transponder compatible with the immobiliser. This guarantees that only the right key is able to start the engine. If the chip inside the Peugeot key is damaged, it won't transmit the proper signal to the vehicle.
This is a very common issue that is often caused by water damage. This is most common in colder climates. the vehicle may have been exposed to snow or rain. In this case, contact a reliable locksmith who has the tools and equipment required to modify the key. They will also have all the latest technology and equipment needed to make the Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts with the battery may be damaged.
Peugeot replaced the transponder chips by introducing a new model that utilizes electronic components that are mounted on a circuit board. The new system is fantastic when it's brand new, but the circuit boards wear out over time and cease to function properly.
This can prevent the immobiliser from working, so the vehicle won't start. If this happens, it's a good idea to call a Peugeot specialist or locksmith.
G28 that is common is when the battery in the key fob starts to die, this causes the blade of the key to stop being able to feed into the lock. A locksmith from your car will replace the battery, and then cut a fresh blade for you. This is a quick solution.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it may be due to a faulty receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer, which is responsible for controlling the centralized locking system within your Peugeot vehicle.
The rubber seals on the key fob keep water from getting to the electronic chip. Water can damage the chip when it is exposed to water for long periods of period of. The high salt content in the pool or ocean waters can cause damage to the key fob when it is submerged.
If your Peugeot spare key fob stops working then you'll have to get the module replaced. This is only done by an Peugeot specialist or an expert auto locksmith. In contrast to other vehicles, Peugeot keys are protected by an unique immobilizer system that requires the correct programming in order to start the engine. This is why you should trust an experienced Peugeot locksmith for the job of programming and creating the replacement.
Computers with faulty on-board computers
The on-board computer of your Peugeot is responsible for many of the systems inside your car, including power windows and airbags. When something goes wrong in these systems, it'll typically display a code that indicates the problem. This code is stored inside the system and remains there until the problem is solved. This may require the on-board computers to be replaced.
One of the most common reasons for the light coming on is loose or corroded connection in the airbag sensor. This could be due to wear and tear, aging or exposure to moisture and salt. This issue should be addressed as soon you can, because an airbag malfunctioning could pose a risk in the event in the event of an accident.
If your Peugeot is showing a card that is not being detected error, then the key battery in the key fob might be weak or dead. This will prevent the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock key on the key fob, and then trying to start your car. If this fails it is because the battery of the key must be replaced.