Subaru Xv Replacement Key: The Secret Life Of Subaru Xv Replacement Key
How to Change a Subaru Spare Key
When you lose your Subaru car key, you should call a locksmith. Locksmiths usually can cut keys for you at a lower cost than the dealer.
Subaru car keys are generally either intelligent "push-to-start" fob remote keys or basic metal keys. The Fob keys have a chip inside and requires reprogramming.
Keyless Entry System
The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. These remotes make use of keys in your car to communicate with your vehicle's computer.
Some models of Subaru offer a little-known feature called PIN Code Access. You can use a customized number sequence to open and start your car. If you have a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that comes with this feature, check the owner's manual to learn how to use it.
It's possible that the battery in the key fob is dying. You can check the battery life of your key fob with an electronic tester that you can carry around or a multimeter that you have in your garage.
The next step is to remove the key fob from its case and inspect the circuit board of its transmitter. The board will contain one or two sets of 8-digit numbers, so note down the first set so you can recall it later. After you've completed this, you can begin programming your key fob at home. This procedure differs based on the model and year your car. However, it's generally easy enough to do yourself.
Key Fobs
Subaru's latest models have key fobs that don't just unlock doors, but also turn on lights, lock the gas cap, and even start the car. This last trick is particularly helpful if you've been at the gas station only to find that your car won't start because the key fob battery failed.
If your Subaru is old or new it's likely that the key fob can be replaced with little difficulty. It's important to remember that models with high levels of technological sophistication may require an appointment at the dealership. With some effort and time, you can create your own key fob replacement.
Begin by opening the case and inspecting the circuit board of the transmitter. (Instructions on how to open the case are usually provided in the owner's guide). It should contain two or three sets of serial numbers each one of which is 8 digits long. Keep the first series of numbers handy for later for reference.
Then, get into the driver's seat and close the doors. Turn the key to start the vehicle before turning off after ten revolutions. Press the lock button on your key fob, then open the door. This will verify that your doors are working properly. Close the door, and then take the key off. You should hear the chime from your vehicle once more to indicate that the key fob has been programmed.
Ignition System
The battery for the key could be dead If your Subaru keys aren't functioning as they should. If you know how, you can replace the battery in your key fob yourself. A replacement battery is not expensive and relatively easy to locate. If your keypad doesn't respond to your commands, it may be a problem with it. It's recommended to visit a dealer to get a spare key. They'll ensure that the key is genuine Subaru key, that is in warranty, and that it is programmed to your vehicle. This is a lot safer and more convenient than purchasing an aftermarket key from a company on the internet.
The dealer is also able to cut a key for you if you provide your VIN number as well as evidence of ownership. They'll use this information to create a code for the new key so that it can be accepted by your immobilizer. This is a much more complicated procedure than cutting a key by hand and the dealer will charge more for it.
Once the new key has been programmed, you can replace it with your working key. It will only take you five seconds to insert the new key, so be sure to keep your working key close to the ready. Once the security light stops flashing then you can take out the new key and examine it to make sure that it's functioning correctly.
Battery Replacement
One of the primary features that make Subaru fobs so valuable is their ability to switch on your car's power windows as well as sunroof with a single touch of a button. The battery inside your Subaru fob isn't designed to last forever, and will require replacement at some point. The good news is that replacing the battery is a straightforward procedure that you can carry out yourself with the help of this quick guide from Capitol Subaru.
You'll need to locate the small gap that separates the front from the back of your keyfob. Using a small flathead screwdriver, you can break the seam open and reveal a small compartment inside that houses the battery. Install the new battery and ensure it is facing the right way. Remove the old one. Once everything is put together and you are able to use your new key fob to lock, unlock, and start your vehicle without difficulty!
Always have subaru replacement key fob , particularly if the one you have is broken or lost. A new key can be bought at your local auto dealership or you can request one made by an locksmith. In either case, it's vital to get your key fob operating properly quickly so that you can drive in a safe manner!