Sage Advice About Fiat Panda Key Fob Replacement From A Five-Year-Old

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the Fiat 500 is a convenient way to unlock the doors and get started the car. However, there are a variety of reasons why the key fob might stop functioning. These include a dead battery water damage, receiver module issues, or interference.

This listing is for an NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob not functioning. Modern key fobs operate with a limited range of operation, and should be within only a few feet from the car to operate. If you are further away from your vehicle, and you push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a new one from a reputable brand such as Panasonic Duracell or Energizer. They can be found in the local hardware store or on the internet.

After you've replaced the coin cell battery, you can test it by standing close to your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should be able to operate the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module in your car. Water damage can happen in a variety of ways, such as a simple splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob is likely to need to be reprogrammed by a professional locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean or wash it in a washer. Saltwater can be particularly harmful to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not good to get the fob wet but don't give up if you accidentally drop it in the water or don't remove it from your pants pocket.

First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Check the fob to check if it's working. If the fob doesn't work, it may need to be changed. This is usually done by an auto locksmith or dealer.

If your key is old and has not been programmed for your car, you will need to replace it completely. A professional locksmith in the automotive industry can do this job. The locksmith will have to cut the key to match the ignition of your car. The locksmith will also need to reprogram the fob into the vehicle's system. This is a simple and cost-effective process that can be completed within the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote's range is of 30 feet, so in the event that you are far from your car it will not respond to your commands. This can easily be resolved by moving closer to your vehicle until it begins responding.

If your fob isn't working after you replace the battery inside the coin, which is also known as a "button", "watch" or "button", it could be due to an issue with the internal circuit board. Reprogramming your fob can resolve this issue. You can find the instructions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

It is possible to replace the metal clips that keep the coin battery in place. If they lose tension, it can prevent the coin battery from sitting properly and result in the malfunction of your remote.

In rare cases the fob could be desync'd with your vehicle because of software or hardware issues. This can be a major trouble, but you could frequently fix this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In some instances they might need to reinstall the software on your body control module, as well.

Interference

In addition to a dead coin battery The key fob may not be able to transmit or receive signals due to interference. This could happen when the keyfob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons the key fob may not function may be a lack of connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while out of the blue or after trying everything you can do at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, you might have a faulty receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands that are then processed by the vehicle.

Luckily, there is an easy method to reset all of the onboard systems in your 500 keys, including the key fob. Disconnect fiat 500 key fob replacement for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will get rid of any residual electricity and restart the car's computers, which can help you get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to identify the exact cause of problems.