REINFORCEMENT DETALING FOR ISOLATED FOOTING

REINFORCEMENT DETALING FOR ISOLATED FOOTING

जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ

@ETCONP SHORT ARTICLE

Figure1. Isolated footings source: - topper

I.   መግቢያ/introduction

There are different types of foundation based on number of factors.

The isolated footing is the most simple and popular and simplest types of foundation used worldwide. Foundation is very important to the building. Ultimately the entire load of the building is transferred to the ground through the foundation. Isolated footing are the most commonly used footings for reinforced cement concrete column because it is simple and most economical. An isolated footing is used to support a single column. Isolated footings are independent footings which can provide for each column.

የተለያዩ አይነት foundation አይነቶች አሉ። Foundation የምንመርጠው የተለያዩ ምክንያቶች አሉ።

ለምሳሌ ፡ -

➪ የአፈር የመሸከም አቅሙ

➪Type of structure

➪ Purpose of the building

➪Types of the soil

እኚ ሁሉ የምንጠቀመውን የ foundation አይነት ይወስናል።

Isolated footing የ foundation አይነት ሲሆን ከሌሎች የ foundation አይነቶች ጋር ስናነፃፅር ወጪ ቆጣቢ እና ለአሰራር ቀል ያለ በኣብዛኛው ጊዜ የምንጠቀመው የ foundation አይነት ነው። ይህ የ foundation አይነት ለእያንዳንዱ column አንድ footing አለው።

II.    This type of footing is used

1.    Column is not closely spaced

👉🏿ውድ የ @Etconp ቤተሰቦች የ አንድ ህንፃ column ቢጠጋጋ ምን ችግር አለው?

👉🏿 Dear @etconp members what if the column are closely spaced?

2.    Load on the footings are less

3.    The safe bearing capacity of soil is generally high

The isolated footings essentially consists of a bottom slab. There are three basic types of bottom slabs are   

1.    Pad footing with uniform (thickness)

2.    Steeped footing (with nonuniform thickness)

3. Sloped footing (trapezoidal section)

Figure2.types of isolated footing source:-nptel (National Program on Technology Enhanced Learning

III.           REINFORCEMENT DETALING OF ISOLATED FOOTING INCLUDE

1. Concrete cover of reinforcement

According to (INDIAN STANDARD) IS 456-200 the “minimum thickness to main reinforcement in footing should not be less than 50mm if footing is in contact with the earth surface directly, and 40mm for external exposed face such as surface leveling PCC. If the surface levelling is not used, then it is required to specify a cover of 75milimeteres to cover uneven surface of excavation.” PCC means plain cement concrete ሌላ ነገር አይደለም lean concrete ማለት ነው። ህንዶች RC ለማለት RCC፣ Grade beam ለማለት plinth beam ነው ሚሉት።  

2. Minimum reinforcement and bar diameter  

Minimum reinforcement shall not be less than 0.12 percent of the total cross sectional area.

The minimum diameter for main reinforcement should not be less than 10mm.  

3. Reinforcement distribution in footing

In way RCC footing, the reinforcement is distributed uniformly across the full width of footing. In two-way square footings, the reinforcement is distributed across the full width of footing along direction. However for short direction, the reinforcement is distributed in central band as per calculation below in figure 4. The rest reinforcement in short direction is distributed equally on both sides of central band.

Figure3. Two way square footing source: - Bayan Mustafa


Figure 4. Reinforcement distribution in square isolated footing source:-NPTEL

4. DOWEL REINFORCEMENT

Dowel reinforcement is used to tie the isolated footing from above column. With regard to dowel reinforcement development length, the development dowel bars in to column and the isolated footing shall be provided clearly shown in design drawings.

Figure5.isolated footing section source: - topper

5. Lap splice

Splice length of dowel and column reinforcement shall be checked to prevent bond failure of the dowels in the footing and to prevent failure of the lap splices between the dowels and the column bars

Fig6. Anchorage reinforcement source:-NTPEL
FIGURE7. PLAN VIEW OF ISOLATED SLOPED FOOTING SOURCE: - NTPEL

IV. ADVANTAGE AND DISADVANTAGE OF PAD FOOTING

👉🏿 ADVANTAGE
➪ Its type of shallow foundation so it requires little excavation
➪ Can be designed to accommodate tight sights
➪ Economic due to control of foundation size
➪ Reinforcement for shear and tension can be added
➪Easy to construct
 
👉🏿 DISADVANTAGE
➪ Foundation size can be very large cope with high points load
➪ Limited foundation suitable to point loads of framed building
➪ Weak against different settlement that may affect the building
➪Deep excavations for foundation would require support to prevent caving in
➪Weakness against uplift force, wind forces and earthquake forces

Source:-AAiT lecture note  

v.       List of figure

Figure8. Arrangement of bars for isolated footing source:-topper
Figure9. Casting concrete for isolated footing source:-@topper
Figure10. Rigid spread footing and flexible spread footing source:-ntpel
Figure11. Plan view and section for spread footing (uniform) source:-ntpel
Figure12. Plan, section and 3D of spread footing source: - CTCIVIL.IR
FIGURE13. Bar details of spread footing source: - nptel
Figure 15. Sloped isolated footing source:- ntpel
Figure 16. Section and elevation for square, rectangular and circular footing
Source: - ntpel
Figure17.flexible spread footing and rigid spread footing source:-ntpel

Source:-ntpel

              Topper

               AAiT

              CITCIVIL.IR

                BAYAN MUSTEFA

join us on telegram:-@etconp












Report Page