Quiz: How Much Do You Know About Replacing Lock On Upvc Door?
Replacing Lock on uPVC Door
To replace the lock, you must first take off the screw holes and handle. This is usually simple to do.
Next, locate the screw that is inserted into the barrel of the lock. This screw is typically different in colour from the screws that are used in other locks, and is located on the outside of the faceplate of the lock.
Take the Cylinder off
The first step to change the lock on your door made of upvc is to take off the current lock cylinder from the door. This is a simple procedure that can be done within 30 minutes. All you need is a screwdriver. The Euro cylinder screw is usually found on the inside of the door, right next to the lock cylinder. The screw should be easy to identify as it is usually different in colour from the other screws. Remove this screw and keep it in a safe location.
After the cylinder has been removed, you can start working on the removal of the handle. To do this, you must open the door to gain full access to the inside edge of the door and the side of the faceplate of the lock.
Remove the screw that binds the handle to the door using the screwdriver. After this screw is removed, you should be able to pull the handle towards you, and the rest of the mechanism will fall out of the door.
If you are having trouble taking the handle off then you'll need to take off the screw that is holding it to the stud inside the door frame. You can use a screwdriver or drill to remove the handle. Be careful not to strip or cross-thread it.
If you're ready to replace the cylinder, be sure it is the right size for your door. Cylinders are measured according to two factors: (a), the distance from the center of the Fixing Screw to the bottom of the cylinder, and (b), the distance between the keyhole's hole the keyhole and edge of the lockplate.
Take the handle off
The good news is, the moment your upvc handle starts to become stiff, floppy, or loose, it's an easy problem to fix. The cause is usually due to wear and tear on the cylinder or other internal components of the multipoint lock, which are inside the door between the handle and its frame. Weather conditions, heavy usage or aging can cause the upvc locks to wear. This could lead to problems with the locking and closing mechanisms of the door.
The cylinder may wear out and make it difficult to turn the key. The lock could also become stiff causing the handle to loosen. The cylinder is easily replaced, and this is a straightforward process. It can be done yourself, but you will require some knowledge about the mechanism's operation. The first step is to unhook the handle that will allow you to gain access to the cylindrical and replace it with a new one.
To do this, you will need a screwdriver and a tape measure. It is important to be aware of the size of your current cylinder because it will allow you to order an appropriate replacement. The cylinder is the part that allows you to lock your upvc door, and it is important that you ensure that you get an identical replacement size.
To get rid of the old cylinder you'll need to remove all the screws that hold it. Be careful not to strip the screws, as this may make it very difficult to remove them again in the future. Once the screws have been removed, the cylinder should be easy to remove.
Take off the Lock Barrel
Upvc is a very durable material and designed to keep you and your family safe. They come in a wide range of styles and colors that can suit any decor. These doors are also thermally efficient and maintenance-free. However, window lock repair without their drawbacks. The locking point, or barrel lock, may get faulty over time and need to be replaced. It's a simple process however, you must be aware of some things prior to beginning.
To get to the screw that holds the lock cylinder, you will have to take off your door handle. It's typically a different color from the other screws and can be found at the edges of the door, near where the keyhole is located. Take out this screw and put it in a safe location. Slide the handles out on both the outside and inside of the door. Be sure you do this slowly and not too fast as it can harm your uPVC door.
Once you have removed the handles, use a screwdriver to remove the screws that attach them to the frame of the door. This will allow you to gain access to the support pins that are holding the cylinder in place. After that, you can try wriggling and pulling the cylindrical to see if it is loose. If it does then pull it back towards you and then out the socket.
After you have removed the old lock cylinder, it is essential to replace it with a new one that has anti-snap and anti-bump security. It is recommended to have an expert locksmith do this for you, but you can do it yourself with the appropriate tools. This is a fairly simple task that should take 5 minutes to complete.
Install the New Cylinder
A upvc lock could be damaged or broken in a number of different ways. For example the cylinder might be damaged or not working as it should. It is essential to select the correct size replacement for your upvc door lock. If the wrong lock is installed, your doors may be more vulnerable to the 'lock snapping technique which is the reason for 25% of burglaries.
To prevent this from happening to avoid this, it is crucial that the correct cylinder is installed and the procedure to do so is relatively easy and takes just five minutes. You will need a screwdriver to remove the screws that are connected to the faceplate on the handle and the cylinder. Once this is done it's a simple task to switch them.
Before you begin be sure that the handle is in a position to open and that you have complete access to the inside edging of the door as well as the handle's faceplate that holds the lock cylinder. This is to ensure that you are able to easily disconnect the lock cylinder, without having to move the handle on the door to expose any internal parts of the handle frame.
The next step is to take the old cylinder out and measure it, you must know the overall length as well as the size of the cam that is used to lock and unlock the door. This will enable you to locate a replacement cylinder that's the same or even smaller. This is the most important aspect of the whole process. A cylinder must be flush with the backplate of the handle and have no more than 5mm from it.
Install the Handle
A upvc lock can jam if something breaks inside the case which controls the bolts that retract into the keep plate or strike. This is usually fixed by altering the Allan key underneath the hinges. However, this could cause stress on the parts within the central casing, and it is best to call in a professional.
It is crucial to have quick and easy access to both sides when changing the handle. It is essential to use the correct tools. It is a good idea to also prop the door up so that it does not close during the process.
First, loosen the screws holding the handle in position with the help of a screwdriver. Once these are loosened the handle can then be removed. Once the cylinder and handle have been removed, it's now time to put in the new handle. Make sure that the new handle fits the existing central cylinder and cylinder. Check the length of the spindle on the lever you have currently to determine this. Verify that the screw fix centre on the handle is identical to the screw fix centre on your current cylinder or hole centre.
Replacement handles from Fab & Fixed are available in a variety of styles and are designed to last. These handles are ideal for those looking to upgrade their upvc handle and improve home security. Having the right handle will ensure that your house is secure and safe, and won't be easy for burglars to break into.