Modern Packaged Boiler Operation, Maintenance and Training
The latter area of the 20th Century saw the introduction of more stringent boiler manufacturing standards, particularly in relation to welding technology and inspection, and the evolution of digital control systems that now offer an unsurpassed degree of reliability. The modern, micro-processor based, high-integrity, "Boiler Control System" (BCS) has the ability to perform most of the tasks traditionally undertaken by the qualified operator allowing extended periods of automatic operation without any human intervention whatsoever. An integral feature of modern packaged boilers is that they are designed to operate unsupervised for extended periods.
The amount of human supervision and operator training requirements are dependant on the amount of sophistication of the "Boiler Control System" (BCS). They are defined in local boiler codes and standards and differ widely between jurisdictions. For example, in some, a high-pressure boiler is defined as any boiler operating above 1 BAR (approximately 15 psig) pressure and, regardless of all the considerations, it must constantly be beneath the control of an appropriately qualified operator. Other jurisdictions impose capacity constraints on unsupervised operation however in many, boiler codes and other relevant legislation have already been revised and extended to accommodate the demand from industry for this type of boiler.
Industrial boilers of all types generally belong to one of three categories when it comes to their operational and qualification requirements. They are:
? Attended Boilers;
? Limited-Attendance Boilers;
? Unattended Boilers.
What is a "packaged boiler"?
The word "Packaged Boiler" can be used to describe a boiler that's factory built and delivered either fully assembled or, as pre-built modules that may be easily assembled on site. It is essentially a self contained unit complete with a control system and all equipment necessary for operation. The boiler manufacturer assumes responsibility for all components and after delivery all that's needed is is for this to get in touch to the steam distribution system, water, fuel, and electricity supplies. Almost all small and medium sized boilers manufactured today are packaged boilers plus they could be the conventional firetube or watertube type, including their derivatives or, hybrid boilers such as once-through coil and electrode boilers.
What is an attended boiler?
Until relatively recently, the vast majority of steam boilers operated in the "Attended" mode. That is, they were required to have an appropriately qualified operator on-site and in the immediate vicinity of the boiler constantly that it had been operating. Since the introduction of micro-processor based technology to boilers from around 1990 onwards, many traditional attended boiler owners have upgraded their control systems. Given also that Go to this website -processor based controls are actually an almost universal feature on new packaged-boilers, the original boiler attendant is now an endangered species in small to mid-sized plants supplying process steam. At the very least, their role has changed from that of direct, hands-on operation to 1 of supervising the operation of the BCS and performing tasks that ensure its continuing integrity and compliance with certain requirements of boiler codes and standards.
Boiler operation has evolved to the stage that in lots of jurisdictions, fully attended operation is unusual outside of large, complex plants. The exceptions are large power utilities, chemical recovery boilers and similar integrated processes where in fact the boiler is a key component.
what is a limited-attendance boiler?
The Limited-Attendance mode of operation allows for periodic checking of the boiler at set minimum intervals rather than continuous attendance. An integral feature of limited-attendance boilers is they may at any time be brought under the control of an appropriately qualified operator and operated in the fully attended mode under continuous supervision.
Many older packaged boilers and the ones which were upgraded from attended status are classified as limited-attendance due to the fact their control systems do not achieve exactly the same standards of integrity and reliability as do modern micro-processor based systems. Many also include provision for manual intervention which in most jurisdictions disqualifies them for consideration for unattended status.
What's an unattended boiler?
An Unattended Boiler is essentially a fully automatic boiler that operates beneath the continuous supervision and control of a sophisticated, micro-processor based, BCS. The BCS controls the entire boiler function like the energy input management system (on oil and gas-fired boilers often called the "Burner Management System" or, BMS), the water level management system, the alarm system, the pressure controls, trip devices, all instruments and circuitry.
A key feature of this kind of boiler is that in most jurisdictions boiler codes and standards dictate a boiler that's classified as unattended should be beneath the continuous supervision and control of the BCS always that it is operating. The unattended boiler may only be operated in unattended mode. It could not be operated in attended mode under any circumstances even for brief periods and even if a qualified operator can be acquired. Used, the BCS employed on an unattended boiler has no provision for manual operation. In case of a control system fault or perhaps a potentially unsafe condition, the BCS will shut down the boiler and lock-out the energy input system. It will prevent a boiler restart until such time that the control system fault has been repaired or, the potentially unsafe condition has been addressed and all the BCS inputs indicate that the boiler is in a safe condition.
The BCS is equipped with some method of recording all major events that cause the alarms to activate. On early unattended boilers this is typically a simple printer that recorded such events on a line-by-line basis. Newer systems however, store the information in the onboard micro-processor memory for a long period. They typically record a much wider range of information to supply improved oversight of boiler performance and, are sometimes integrated with a plant-wide information system which facilitates the remote storage of data for extended periods.
The unattended boiler is a relatively recent phenomenon. Traditionally most boiler installations operated beneath the continuous supervision of a qualified operator although in lots of jurisdictions, some small boilers were permitted to operate in limited-attendance mode. Until very recently, in most jurisdictions unattended boiler operation was at the mercy of strict constraints. Typically, permissible maximum operating pressure and design output were severely limited and in lots of locations those constraints still apply, at least on paper. In recent years however, boiler codes and standards in lots of jurisdictions have already been extended to accommodate this sort of boiler and in others it has become quite common for local regulatory authorities to grant exemptions on a case-by-case basis.
With the advent in recent years of improved manufacturing standards and the rapid evolution of sophisticated, increasingly reliable micro-processor based control and monitoring systems, most small to mid-sized packaged boilers from reputable manufacturers now incorporate a high-integrity BCS as standard equipment. Where unattended operation is permitted, they may only require inspection and operational certification by an accredited inspection body to make sure compliance with National and local standards.
Limited-Attendance vs Unattended Operation
To achieve Limited-Attendance or Unattended classification, the boiler is subject to strict statutory oversight covering operation, maintenance, servicing and record keeping. Boiler codes and standards require that boilers in either category be equipped with the very least, specified inventory of safety equipment that will automatically shut down the boiler in case of a potentially unsafe condition.
The classification put on a particular packaged boiler will depend largely on the sophistication of the BCS or, sometimes, the type of fuel that is fired. For example, a 10 MW boiler firing natural gas may achieve unattended classification in which a similar 10 MW boiler from exactly the same manufacturer but firing solid-fuel may be classified as limited-attendance. Firing solid-fuels, particularly people that have a variable moisture content, is sometimes something of a black-art requiring a degree of skill and experience. In this author's jurisdiction, unattended solid-fuel boilers are nevertheless not unusual even for quite large boilers over 20 MW capacity and frequently in multiple boiler installations.
The key differences between your Limited-Attendance and Unattended modes of operation are:
Limited Attendance
? An appropriately qualified operator or responsible person must be on-site at all times that the boiler is in service;
? Codes and standards usually require that the boiler be continuously supervised during startup and shutdown periods;
? During normal operation, the limited-attendance mode allows for periodic checking of the boiler at set minimum intervals rather than continuous supervision;
? Limited-Attendance boilers may anytime be brought beneath the control of an appropriately qualified operator and operated in the fully attended mode under continuous supervision;
? The operator or responsible person must be on-site always that the boiler is in service and should be immediately available if required.
Unattended
? Where unattended operation is permitted, a professional operator isn't a mandatory requirement. The boiler could be supervised by an appropriately trained "Responsible Person";
? The operator or responsible person may leave the site provided that they're available to respond to boiler outages. That is usually achieved by a pager or cellphone signal transmitted by the BCS;
? In lots of jurisdictions, unattended boilers may start up and turn off automatically under the control of the BCS so long as they are suitably equipped to the satisfaction of an approved inspection body;
? Unattended boilers are permitted to operate unsupervised for extended periods and in most jurisdictions that is currently 24-hours. Recent control and monitoring systems innovations by some manufacturers however, have observed that period extended in a few jurisdictions. The 72H notation in Europe for instance, signifies that the boiler is approved for unsupervised operation for periods of up to 72-hours;
? Boiler codes generally in most jurisdictions specifically forbid the provision for manual intervention in the operation of unattended boilers. They must at all times be beneath the control of the BCS. That is, they may only be operated in unattended mode. They may not be operated in attended mode under any circumstances even for brief periods and even if a qualified operator can be acquired.
Training Requirements
Boilers that are certified for unattended operation do not require a qualified operator. This relaxation of the manning requirements imposes substantial obligations on boiler owners, controllers, manufacturers and inspection bodies to ensure compliance with boiler codes along with other relevant legislation and, that boiler supervisory and maintenance staff receive adequate training. Non compliance will more often than not be interpreted as a breach of Occupational Safety and Health legislation that may result in severe penalties particularly if the non compliance is discovered because of an incident or accident.
Accident investigation reports demonstrate that the most frequent contributing causes to boiler accidents are operator intervention with the safety controls, inadequate maintenance, device failure following maintenance by unqualified personnel, isolation or deliberate disablement of the safety devices, inappropriate operating practices and inadequate water treatment. Automatic controls are not a complete substitute for supervision. A measure of supervision by way of a qualified operator or perhaps a trained Responsible Person acquainted with the BCS and the operation of the boiler plant is an essential feature of safe operation.
Unattended boilers that are operated in strict compliance with the manufacturer's recommendations, boiler codes and standards have an excellent safety record worldwide. Because they are made to operate unsupervised for extended periods, routine operating, maintenance and inspection requirements are generally more stringent than for other styles of boilers. The BCS and its associated safety devices clearly play an integral role in the safe operation of this type of boiler and so are therefore at the mercy of strict compliance with routine testing procedures by the trained Responsible Person and the approved maintenance contractor. It is extremely important that there should be a high level of confidence in the integrity of the BCS and the routine testing procedures should therefore be regarded as a important element of safe operation.
Although those tests are usually universal in nature, you can find differences within their implementation between jurisdictions. It is therefore essential that the boiler owner, controller and trained Responsible Person understand that they have a responsibility to familiarise themselves with the local codes and regulations deciding on this sort of boiler. Failure to meet that obligation will most likely be interpreted as a breach of OSHA regulations. If in doubt, you need to seek clarification from your boiler inspector, inspection body, the boiler manufacturer or the neighborhood regulatory authority.
Who is the boiler controller? - roles and responsibilities:
Boiler codes and standards generally require that unattended boiler installations have a nominated "Controller". This may be the owner or, a person nominated by the owner to execute that role. The Controller does not necessarily must be closely associated with hands-on, day-to-day operation but instead, to provide general oversight of the boiler operation and maintenance.
The Controller's responsibilities include:
? Ensuring compliance with the Boiler code or relevant standard including the maintenance of appropriate operational and engineering records;
? Making certain the boiler is supervised by appropriately qualified or trained persons;
? The implementation and maintenance of a Quality Management System (QMS);
? The implementation and maintenance of appropriate safety and environmental procedures and, communications with the correct regulatory bodies for instance, OSHA, environmental agencies, inspection bodies and so on.
The Controller is normally a engineering, maintenance or departmental manager or, someone in the business that holds a qualification or Certificate of Competency in boiler operation.
what is a trained responsible person? - roles and responsibilities:
A "Trained Responsible Person" is a person who is appointed by the controller to exercise day-to-day supervision of the boiler. He or she is not required to hold a formal qualification for instance a certificate of competency but, must be trained to a level specified by the boiler manufacturer or, to a level acceptable by an inspection body or other appropriate regulatory authority. The Responsible Person is not required to have an intimate understanding of boiler technology but rather, a basic degree of knowledge and an understanding of the functionality and roles of the boiler components, mountings and ancillary systems including the fuel, feedwater, and steam distribution systems.
The primary roles of the Responsible Person are to exercise general day-to-day supervision of the boiler operation, verify that control and alarm systems are functioning correctly also to ensure compliance with the routine testing procedures specified in the relevant code or standard and, by the boiler manufacturer. The Responsible Person shouldn't necessarily be likely to diagnose and rectify equipment or system failure. They should be competent to react to alarms, also to take appropriate action which, at a minimum, means that the boiler is turn off safely before calling for assistance.
what's an approved maintenance contractor?:
Compliance with defined maintenance procedures is a key aspect of unattended boiler operation. There were a number of recent catastrophic boiler incidents resulting from inappropriately performed maintenance tasks which in some cases, were undertaken by qualified and experienced tradesmen but, who lacked the expert understanding requirements connected with boiler maintenance.
The "Approved Maintenance Contractor" is a person or organisation with the correct skills, knowledge and experience to keep the boiler and its own components to a typical acceptable by the product manufacturer and the inspection body. They need to have a thorough understanding of the role and functionality of the BCS in relation to limited-attendance and unattended operation.
Boiler codes and regulations define minimum acceptable standards for this role which may differ between jurisdictions. In general, they will require that the nominated organisation be a boiler manufacturer or an unbiased contractor approved by the manufacturer or the inspection body. In organisations which have their own internal maintenance infrastructure, the Controller may apply to the inspection body to nominate the business itself as the approved maintenance entity. In such cases, the organisation must fulfill the requirement that nominated personnel performing the task have appropriate training and experience. That will typically require that nominated staff members can provide proof an appropriate trade qualification or, have received specialist training and also have sufficient experience. For no reason whatsoever should non-approved staff be permitted to perform maintenance on any pressure equipment or the BCS and its field devices including all safety devices and the power input system.