How to Use the Berachain Bridge From Arbitrum for WETH

How to Use the Berachain Bridge From Arbitrum for WETH


The Berachain bridge lets you move native ETH from Arbitrum One to your address on Berachain. Add Berachain to MetaMask, connect your wallet, choose Arbitrum One as the source and Berachain as the destination, then enter an ETH amount that leaves enough for Arbitrum gas. Confirm an address you control, review the quote, and sign the transaction. The transfer is complete when WETH appears at that address on Berascan.

Start with ETH on Arbitrum One in MetaMask. Arbitrum One uses ETH for gas, so the wallet needs enough for both the amount you send and the transaction fee. Native ETH needs no token approval: you sign one source-chain transaction. To make that transfer, open the Berachain bridge and use the Berachain crypto bridge to move your ETH to Berachain.

How Do You Use the Berachain Bridge From Arbitrum One?

  1. Prepare MetaMask to view both chains. Confirm that your ETH is on Arbitrum One, which has chain ID 42161. Add Berachain mainnet to MetaMask before starting and verify its chain ID is 80094. This prepares the wallet to show the destination network after the transfer. You also need a receiving address you can use on Berachain. If you are using your ordinary MetaMask account, select that account on Berachain and confirm its address before continuing.
  2. Connect MetaMask and set the route. With the Arbitrum account holding your ETH selected, connect MetaMask to the bridge. Set Arbitrum One as the source and Berachain as the destination, then select native ETH as the asset to send. Keep the direction in mind while reviewing the transaction: the ETH leaves Arbitrum, while the received token will be recorded on Berachain. A balance shown on Arbitrum is the starting balance, not evidence that the destination transfer has finished.
  3. Enter an amount that leaves ETH for gas. Subtract a small Arbitrum gas buffer from the ETH in your wallet before choosing the transfer amount. Using Max can commit the entire balance to the transfer and leave nothing to pay for the Arbitrum transaction. Say your wallet holds 0.1 ETH and you expect to bridge all 0.1 ETH. The transaction still needs gas, so the amount available to send is less than the wallet balance. Use MetaMask’s current gas estimate when deciding how much to leave; a fixed buffer may be too small when fees change.
  4. Confirm the destination address before signing. The address must be one you control on Berachain. An ordinary MetaMask account is controlled by the same key when you switch between these two networks, but a Safe or another smart-contract wallet is different: its Arbitrum address may have no wallet contract deployed at that address on Berachain. Take an Arbitrum Safe whose owners expect funds at the same-looking Berachain address. If that Safe has not been deployed there, WETH can arrive at the address while the owners cannot use the Arbitrum Safe to move it. Look up the proposed destination on Berascan and confirm the Safe exists on Berachain before using it. Otherwise, choose an ordinary MetaMask account you control or a Safe already deployed on Berachain. Do this now, while you can still change the destination.
  5. Review the transfer quote. Read the expected WETH amount, the quoted fee, and the estimated transfer time before proceeding. Compare the receiving address with the one you checked, character by character or against a trusted saved address. The quoted amount tells you what to look for on Berachain; it may differ from the ETH amount sent if the transfer has a fee. An estimate is useful for deciding when to check again, while the onchain record tells you whether the transfer has arrived.
  6. Sign the Arbitrum transaction and save its hash. Confirm the transaction in MetaMask after checking its network, amount, and gas cost. Native ETH requires no separate approval transaction, so this is the one transaction you sign on Arbitrum for the transfer. Save its transaction hash once MetaMask provides it. The hash identifies the source transaction if you need to distinguish this transfer from another one or check whether it was submitted successfully.
  7. Verify the WETH at your destination address. Open Berascan, Berachain’s block explorer, and inspect the receiving address you confirmed in step four. Look for its WETH token balance or the incoming WETH transfer. That onchain record is the completion check. Then switch MetaMask to Berachain to view the wallet there. If MetaMask does not immediately show the token, use the Berascan record to confirm whether WETH has arrived before deciding that the transfer is still pending.

Why Does ETH Arrive as WETH Instead of BERA?

ETH sent by this route arrives on Berachain as WETH, an ERC-20 token, because Berachain uses BERA as its native gas token. The token name changes how you look for the result: inspect the WETH balance at your address, not the wallet’s BERA balance. Bridging ETH through this route does not turn it into BERA. If you intend to make transactions on Berachain after receiving WETH, you will need BERA for gas.

That distinction also explains a common false alarm. You sign on Arbitrum, switch MetaMask to Berachain, and see no increase in the wallet’s native balance. You expected ETH to appear in the same place it occupied on Arbitrum; what actually arrived is WETH in the token balance. Berascan lets you check the address directly. Once WETH appears there, the bridge from Arbitrum has delivered the asset described by the quote.

How long does a transfer from Arbitrum to Berachain take?

The transfer time depends on the live estimate, Arbitrum confirmation, and destination processing. Review the estimate before signing, then use the saved Arbitrum transaction hash and your Berascan address to follow the transfer. The WETH balance at the destination is the useful endpoint, even when the estimated time has passed.

Can I receive BERA directly when bridging ETH?

This ETH route delivers WETH on Berachain, not BERA. BERA is the gas token needed for later Berachain transactions. Plan for that separate need if you intend to use the received WETH in Berachain DeFi.

Is there a minimum amount to bridge from Arbitrum?

The usable minimum depends on the current transfer quote and fees, so check the amount shown before signing. You also need to leave ETH on Arbitrum for gas. If the amount you want to send is too small after those costs, choose a larger amount or wait rather than spending your entire gas balance.

  • Add Berachain mainnet to MetaMask and confirm chain ID 80094.
  • Choose an amount that leaves Arbitrum ETH for gas, and verify the receiving address works on Berachain.
  • Review the quote, sign once in MetaMask, and save the Arbitrum transaction hash.
  • Confirm WETH at your receiving address on Berascan.

Report Page