How To Solve Issues Related To Door Lock Change
How to Do a Door Lock Change
The change of your door lock is an easy and affordable way to improve the security of your home. However, the procedure isn't for all. It requires some expertise and perseverance.
The cylinder is contained within the knob body. The cylinder is responsible to recognize the key when it is inserted in the lock.
Remove the old lock
The first step to replace a door lock is to get rid of the lock that was previously in use. This is a relatively simple procedure, but there are a few things to keep in mind. Make sure the new lock is compatible with your door. This will ensure that it fits snugly and doesn't create a gap around the latch or deadbolt plug.
Once you have removed the latch plate, look for two bolts or screws on the inside of the casing, which secure the casing and halves of the lock. Take these screws off using the help of a screwdriver, and then remove the lock from the door. If you have a mortise locking mechanism there is a set screw that holds the handle to the spindle. Remove the doorknobs by unscrewing the screw using the help of a screwdriver.
You must also remove the latch and deadbolt plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise you must measure the distance between your lock's case and the door edge to ensure that the new lock will fit.
You might want to change your lock for a variety reasons, such as when you suspect that someone else holds the key or you've got an incoming roommate. In any case, you can save money by removing the lock yourself rather than paying an expert to do it. The process is simpler than most people think, and it can be completed in just a few minutes.
Remove the trim and handle of your door. With a flat screwdriver take off the trim. You should be able twist off the majority of it. In certain cases, you may even be able remove the handles completely. Next, look for a hole on the inside of the handle and then insert an unstraightened clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Then, look for another small tab on the interior of the lock and press it with a screwdriver that is flat. After the spindle is removed, you can then take off the cylinder and housing.
The process of selecting a new lock
There are many options to choose from when it comes time to pick the right lock. Look at different types of locks and find one that matches the style of your door. Think about the backset, which is the distance between the edge and the middle of lock hole. Also, consider the cross bore, a small hole at the edge of your door's frame. Select a lock that will fit the door's thickness and the swing.
Most door locks have been graded by BHMA and the American National Standards Institute to give you an idea of how they stand up to use and how difficult to disable or pick. A grade 3 lock could be ideal for a quiet suburban apartment complex, whereas a grade 1 lock might be more able to withstand the traffic that is frequented by a storefront on a busy city street.
Most smart door locks require a digital key code to open. If you are concerned about hacking, or other security concerns, speak to an expert locksmith.
Replacing the cylinder
If your door lock cylinder is broken or damaged you can repair it in just a few minutes by completing a do-it-yourself project. The key is to select the right cylinder and follow the steps that are included with it. The first step is to remove the knob or handle in the event that one is present and then remove the trim around the base of the lock cylinder using the aid of a screwdriver. Once the trim has been removed, you can reach the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder can then be gently pulled out of the door.
Before installing the new cylinder, be sure that it is the right length for the door you are using. With a tape measure, measure the distance between the cylinder's center and the left and right sides. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.
Install the replacement cylinder into the door, and then turn the key. This will align the cylinder with the carrier which is typically on the outside of your lock. Then, loosen the set screw that should be a few turns in the head. If there is a screw located on the edge of the case that is holding the door, you'll have to loosen it.
After removing the lock cylinder after which you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder with the stem of the lock indicator that you can do by pulling out three tabs on the back of the cylinder with needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you should reinstall the strike plate and latch plate, as well as the retaining rings attached to the top of the lock cylinder.
Installing the new lock
Begin by measuring the door's width if you are replacing an existing lock. The majority of residential locksets have a thickness of 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require a thicker door kit. This would include longer screws, or an extension for the spindle or a longer the tail piece for door knobs.
Most locks come with a comprehensive installation guide to help you. Read the instructions carefully prior to beginning the process to ensure that you've followed all the steps. replace upvc window lock will also provide you with an idea of the level of skill required to accomplish the task. You might want to ask a person who has experience changing locks for assistance if you are changing a lock the first time.
It's a great idea cover the holes in the old hardware prior to installing the new lock. This will stop the screws from falling through the holes and will also protect any tiles you might have put in. It also helps prevent potential damage from rust, grime, dirt and. SECURAM Touch comes with a strip painter's tape that is intended to be used for this purpose, however you can also use gaffer's tape or masking tape if you have it available.
After you have removed the screws that connect the interior portion of the lock section to the exterior side then pull it out straight away. It's crucial to do this as quickly as possible to prevent the lock from closing itself in a way that could end up damage the mechanism.
Fit the new latch bolt into the upper cross bore of your new lock, if it comes with one. Make sure to place it in the proper location, which is marked by an arrow. Next, fit the latch plate onto the bolt and screw it into place.
Finally, screw the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it a several times to make sure that it extends all the way into the strike plate and is secure. Follow the instructions that come with your electronic smart lock to program it. This involves downloading an app and registering your e-mail address, verifying your identity and connecting to the wireless network in order to connect your device.