How To Explain Door Lock Change To Your Grandparents
How to Do a Door Lock Change
Door lock change is an easy and inexpensive method to boost your home's security. The process is not for everyone. It requires a certain amount patience and expertise.
The cylinder is located within the knob body. The cylinder is responsible to recognize the key when it is inserted in the lock.
Take off the lock that was previously used.
The first step in replacing the door lock is to take out the old one. This is a relatively easy process, however there are a few things to remember. Make sure that the new lock is compatible with your door. This will ensure that it is secure and doesn't create a gap around the latch or deadbolt.
After you have removed the latch plate, look for two screws or bolts on the inside of the casing, which secure the casing and halves of the lock together. Take these screws off using a screwdriver and then pull the lock from the door. If you have a mortise lock there could be a set screw located at the base of the handle that holds it to the spindle. Remove the doorknobs by unscrewing this screw using the help of a screwdriver.
You must also remove the latch and deadbolt plug from the hole in your door jamb. Then, you are able to install your new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the edge of your door to ensure that your new lock will be able to fit.
It is possible to replace your lock for various reasons, including when you suspect that someone else has the key, or if you have new roommates. In any event, you could save money by removing the lock yourself instead of paying an expert to remove it. The process is simpler than many people think and can be completed in just a few minutes.
Remove the handle and trim of your door. With a flat screwdriver, take off the trim. It should be possible to pull off the majority of it. In some cases, you may even be able remove the handles completely. The next step is to search for a pinhole on the inside of the handle and then insert a straightened clip into it. This will trigger the release mechanism, which allows you to remove the handle. The next step is to look at the inside of the lock for another small tab that you can press using a flat screwdriver. Once the spindle is removed, you are able to remove the cylinder and housing.
The choice of a new locking system
There are a lot of options available when it comes to choosing a new lock. Take a look at the various types of locks and pick one that fits the design of your door. Take into consideration the backset (the distance between the edge of the door and the center of the hole in the lock) and the cross bore (small hole along the edge of the door frame). Also, be sure to choose a lock that will fit the door thickness and swing.
The American National Standards Institute and BHMA have graded the majority of door locks to give you an idea of their longevity and how difficult it is to pick them up or disable them. A lock of grade 3 could be perfect for a quiet apartment complex in the countryside, whereas locks of grade 1 might be more suitable for an area with a lot of traffic, such as a storefront.
Most smart door locks require a digital key code to open. If you are concerned about hacking, or other security issues, talk to a professional locksmith.
Replace the cylinder
If your door lock cylinder is broken or damaged you can repair it in just a few minutes by completing a do-it-yourself project. The trick is to select the correct cylinder and follow the instructions that are included with it. First, take off the handle or knob if it is present. Then, using a screwdriver, take off the trim around the lock cylinder. Once the trim has been removed, you can access the screws that keep the cylinder in place and remove them with the flat-head screwdriver. The cylinder can then be gently removed from the door.
Be sure to measure the length of the new cylinder prior to putting it in place. With an instrument, measure the distance between the cylinder's center and the right and left sides. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key becomes stuck inside.
Place the replacement cylinder inside the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is normally located on the outside of the lock. Then, loosen the set screws that should be only a couple of turns into the head. You will also need to loosen the screw at the edge of the door that fastens the case, should there be one.
You can replace the old lock cylinder with the new one by sliding it into the case and tightening the set screws. It is also recommended to reinstall the piece that connects the cylinder with the stem for the lock indicator and this can be done by pulling up three small tabs on back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you need to install the strike plate and latch plate, as well as the retaining ring that is attached to the top of the lock cylinder.
Installing the new lock
Start by measuring the door's width if you are replacing a lock that is already in use. Most residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will include longer screws, or a longer spindle extension or tail piece for door knobs.
The majority of locks come with a comprehensive installation guide to help you. Before you begin, go through the instructions to ensure you've followed the steps. The guide will give you an idea of how much skill is required to finish the task. If you're replacing a lock for the first time, you might consider asking a more experienced friend for assistance.
Repair My Windows And Doors 's a great idea to tape the openings in the old hardware prior to installing the new lock. This will prevent the screws from slipping out of the holes and safeguard any tile you may have installed in the area. It will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a strip painter's tape, which is designed to be used for this purpose, but you can also use gaffer's tape as well as masking tape in the event that you have it.
After removing the screws that hold the lock's interior half to the exterior, take the lock off immediately. It's important to do this quickly to avoid the lock from accidentally closing itself and harming the mechanism.
Install the new latch bolt in the upper cross bore of your new lock, if it comes with one. Make sure you place it in the correct position, which is usually indicated by an illustration on the faceplate. Then, slide the latch plate onto the bolt and screw it in place.
Finally, screw in the deadbolt and strike plates to the door jamb. Check the deadbolt several times by throwing it to ensure it is extending into the strike plate. Follow the steps that come with your electronic smart lock to program it. This requires downloading an app, entering your email address, confirming your identity, and accessing the wireless network to add your device.