Homemade Fuck Machine
👉🏻👉🏻👉🏻 ALL INFORMATION CLICK HERE 👈🏻👈🏻👈🏻
Просмотренные видео
Показать всё
Скрыть
720p27 сек.Iwannabeacuckold - 398,9 к Просмотров -
720p14 мин.Candygirl Video - 3,9 М Просмотров -
360p31 мин.Widecunt - 1 М Просмотров -
360p5 мин.Gayoxy - 181,3 к Просмотров -
360p6 мин.Cassandra Calogera - 1,2 М Просмотров -
360p13 мин.Babrom - 43,7 к Просмотров -
360p6 мин.Realpeoplefun - 636,9 к Просмотров -
720p88 сек.Sashabooty2000 - 750,6 к Просмотров -
360p5 мин.Fucking Machines - 1,5 М Просмотров -
1080p15 мин.Dahlia Taylor - 152,4 к Просмотров -
1080p7 мин.Emme White - 786,4 к Просмотров -
6 мин.Fred5005 - 53,2 к Просмотров -
5 мин.Bobic001 - 107,7 к Просмотров -
360p10 мин.HomeGrown Videos - 71,4 к Просмотров -
1080p2 мин.Wifenme1 - 86,3 к Просмотров -
1080p4 мин.Masked Milf - 61,7 к Просмотров -
360p3 мин.Aloeran - 98,6 к Просмотров -
360p30 мин.Suicidecamgirls - 1,3 М Просмотров -
360p7 мин.Nika 313 - 1,2 М Просмотров -
360p43 сек.Notmydayjob - 644,6 к Просмотров -
360p3 мин.Jusblaze - 3 М Просмотров -
15 мин.Silversquirter - 31,5 к Просмотров -
1080p8 мин.Big Booty Luna - 220,6 к Просмотров -
1080p2 мин.Megan Ashli - 87,7 к Просмотров -
720p9 мин.Rugedporn - 162,2 к Просмотров -
1080p9 мин.Wirtoly - 36,7 к Просмотров -
XVideos.com-лучшие порно видео, 100% бесплатно.
A Dominant and submissive chat community
Home » Blog » Play, scenes and kink » Like to build your own fucking machine?
Posted on 24/07/201810/07/2020 by MrHamD
I’ve for some time looked through different videos that more or less show details
on fucking machines, and have picked up bits and pieces here and there.
The result is my own working DIY fucking machine. Though, it must be said
that it’s a prototype, noisy and no beauty.
You might find your own way to assemble it.
Have fun!
Below I’ll describe the different parts and possibilities.
Motor.
I’ve looked for geared electro motors with around 250-300 rpm, but most of the available are too small and not strong enough.
My choice was a 12V wiper motor.
It’s not expensive and is powerful enough to do the job. It’s a little noisy, but not too bad.
Wish: 268 Nok
Speed controller.
You need a way to adjust the speed.
This one I chose because it comes
with a box for the electronics and is
cheap. This controller supports any
DC-voltage between 9 and 60 volt,
and should handle any motor in this
range. If you plan to make a
remote-control, please note that the
switch carries the power to the
motor and a remote cable can’t be a
signal cable; the cross section is to
small.
Wish: 113Nok
Power supply.
As the motor is 12V you need a 12V
PSU. There is no info enclosed with
the motor, but my PSU
delives 3A, and that’s not
enough.
I recommend a 5 or 6A version.
Wish: 96Nok
Assembly.
Depending on the way you assemble this, you might need an extension for the motor shaft. I used a 8mm joint nut 25mm long. That enabled me to easyily mount the rotating arm with an 8mm screw.
The length of the arm gives the stroke length, and you have to be able to easily adjust that.
On the end of the arm you need a ball joint. My choice was made for a 8mm threaded rod.
Then you need a shaft joint for connection to the stroking shaft.
Also with 8mm holes and set screws.
The bearings for the shaft need to
be mounted so the joint doesn’t crash
into them whatever stroke length
you might choose.
Wish: 186 Nok
This really is the noisy part of this
machine. I’ve seen this done with
rails for drawers, which might be
better.
Let me now if you find a better way!
As the shafts are 30cm you need to extend them.
My solution was an length extension for drills (100Nok). To fit the shaft I just mounted it on a drill and sanded the end down until it fitted.
Then the real fun part.
The “normal” way to connect the tools are with air tube connectors.
Wish etc are selling sets with these things, and is easy to fit the female end to the shaft with tape etc.
The male part for the air tube connector can be mounted
on a vac-u-lock adapter or
simply a flat plate for
suction.
Hi.
Ive been making my own machine , taking bits of this one and my own ideas. Ive bought the wiper, motor controller and power switch. Im not very electrically minded and im having trouble seeing how its all connected together by the pic. Could you describe what wires go where for me please?
Thanks
Hi!
That depends on what kind of wiper motor you’ve bought.
If it has only 2 wires, they has to be connected to the controller blue and green wires.
(Marked with motor on the controller.)
As this isolated from any electrical ground, it doesn’t matter which goes to which cord.
And on the controller switch, when switching between I and I, the + and – are swapped to the motor to make it rotate the other way.
The powersupply has to be connected +(normaly red) to +(red) on the controller. And -(normaly black) to -(black) on the controller. That should be all…
If your motor has 3 cords you have to look for info on internet, or just test by connecting the motor directly to the powersupply and se how to connect to make it run.
Thanks for your reply. The wiper motor i bought has a male connectorwith 5 ‘prongs’. Christ im terrible. Its connected to the wiper by 5 wires. Green red yellow white and black. Unless i can connect to the wiper with a female connector, i’ll probably have to cut and strip the wires from the connector on the wiper and wire it up to the controller?
Hi. I just replied but it hasn’t shown up so hope im not repeating myself here.
The wiper motor ive got has a male connector with 5 wires soldered onto it. Green red black yellow and white. Unless i find a female connector, im guessing i’ll have to cut the wires and connect to the motor. This is all covered in a clear plastic type silicone.
Hi!
Ouch… You need to find out which of the 5 wires to use.
Then you just cut them from the connector and extend them to the controller, or somehow connect just two of them to the exciting connector and test by connecting directly to the power supply.
Something like this: http://www.scarry-terry.com/wipmtr/wipmtr2.htm.
There your would use Common and Low or High speed.
If you have AVO meter, check by Ohm setting that you’re not connecting your PSU to wires that are driectly connected in the motor.
On the adaptor (power supply), do i have to cut the end of to expose the wires in order for me to connect them to the black and red wires on the controller?
Yes.
But get the motor wires figured out before you connect the controller in between.
Test the motor directly to the power supply first..
Hi. Ive got it going now but its slow as hell. Im imagining its the wiper motor?
Ive just noticed actually the power supply is only 4amps. Would 6 make a significant difference?
Its nothing like my power drill machine lol
The wiper is a 12v motor for a nissan. Its incredibly slow even when the controller switch is on maximum
You night have found the slow input wire.
There should be a high speed wire also, or was that even slower?
Oh right ok i’ll try again. I tried putting the wires into a few terminals on the wiper and nothing worked apart from these two connections. Maybe there’s another faster connection. I’ll try it some morel
Hi, I also made my own f-machine, but I used a stepper motor. lm42p.com
This may be a stupid question. But does the rpm = the thrust per minute ???
Revolutions per minute, how many times the motor shaft spins in a minute, and for a good fuck machine you want the motor to spin at least 200 rpm’s
I made a machine using the parts I purchased from a web site called orgasm alley a 120.00 dollar speed control, and a 150.00 dollar motor, I welded my own frame work, it can be adjusted for height, its portable, not to brag or anything but it kicks ass, or should i say well you know it is a fuck machine, if anyone needs parts I recommend orgasm alley, the machine above is very interesting, I may have build a machine that works as good as the top brands out there, but I cant sell them, because they are just to expensive nobody wants to spend that kind of money, no disrespect but i really dont think a wiper motor does the job, my customers have been asking me to build a machine that i can sell cheaper I think i am going to give it a try using this type of motor, but you know that old saying I have to see it to believe it
I’m working on a F Machine using wood and a drill modeled after this design
https://www.youtube.com/watch?v=4kzwMbj-_WI&list=PLjPD2fLiLJtet-KUqoA9jWiPmkrKS7vFI
Although I’ve found that the drill can’t be mounted the same way because there is some play in the chuck which causes a clunk. My idea is to make something that can be made by an average person in their kitchen with minimal tools.
Hi,
I also made my fuck machine. Please check : https://lm42p.com/diy-en/
My f-machine is a manual one, just a rocking chair with a flat metal fold up chair bungee corded of face of rocking chair. Now I can mount any one of my suction cup dildos to the metal chair and back my ass up on it all night long
This site uses Akismet to reduce spam. Learn how your comment data is processed.
Enter your email address to subscribe to this blog and receive notifications of new posts by email.
The SafeworD/s Club © {2017-2021} All rights reserved. I hereby assert my rights as the author/creator of original material and images posted on this site. No part of this website may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without prior permission of the website owner. Any Person or Persons found to be infringing copyright will face legal action.
Wife Free Free Hd
Deep Ass 2
Janssen Cosmeceutical Body Massage Oil
Lesbian Seductions 69
Brazzers Film Vk
Homemade fucking machine, porn - videos.aPornStories.com
'homemade fuck machine' Search - XNXX.COM
'fucking machine homemade' Search - XVIDEOS.COM
Like to build your own fucking machine? • The SafeworD/s Club
Homemade sex machine, porn - videos.aPornStories.com
'homemade fuck machine' Search - XNXX.COM
Machine: 5412 videos. Dirty Home Clips.
23 Profoundly Disturbing Photos Of Homemade Sex Machines ...
Homemade Penis Fucking Machine - StileProject.com
'fucking machine wife homemade' Search - XVIDEOS.COM
Homemade Fuck Machine
