Do Not Forget Hyundai Key Fob: 10 Reasons Why You Don't Have It

How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is one of the most elegant cars available. Its interior is far superior to competitors like the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's keyfob can do quite a bit for you. It can lock and unlock your car remotely. It also comes with a mechanical key, which can be used in the event that the battery in the fob dies.

Dead Coin Battery

The key fob enables motorists to lock their vehicles and start them without having to insert a physical key into the ignition. It does this through radio frequency signals that communicate with the car's onboard computer.

The battery inside the key fob is responsible for this information and will eventually wear out and require replacement. Depending on your Hyundai model, you could or not get a warning when the battery is about to fail. It's best to keep an extra key fob with you in order to quickly replace the battery when it wears out.

The key fob must be reprogrammed for the car after the new battery has been installed. This can be done using the Hyundai Digital Key app or an OBDII scanner, however it's usually easier to do at your Reno home. To complete this task, follow the instructions in your owner's manual or search YouTube for "how to open and replace a Hyundai key fob battery." Be sure you note down the old battery's number or take a photograph of it before removing it.

Once the key fob has been reprogrammed it should start working once more. If it doesn't, you'll need to visit a dealership for a new one or contact a locksmith on the move. They will have the experience and tools to fix it.

Water Damage

A key fob is a very useful piece of technology. It lets you lock your vehicle from the comfort of home, lower your windows from outside and even start your car. However, it's not a perfect solution and will eventually get worn out due to regular use. Fortunately, the process of replacing a Hyundai i10 key fob's battery is fairly simple and affordable.

Dropping your key card in an puddle, a pool or even the washing machine isn't uncommon and can be rescued, but only if you act swiftly. A wet key fob is bad for electronics. It could cause corrosion, short-circuits, and even failure.

First, try to get rid of as much water as you can. Shake off any visible moisture by flipping the fob. You can also make use of a hairdryer, or place it on a radiator to speed drying. After you have removed as much moisture as you can, consider placing the fob somewhere that is dry and warm where it will dry for a couple of days.

Next, you should attempt to open up the fob, and then remove the battery that was in it. hyundai key fob replacement utilize the same battery that's found in many quartz watches. They are very simple to replace. After replacing the battery, take a photo or note the location of the battery prior to closing the fob.

Contact with the battery is poor

The battery of your key fob may be depleted. This is a typical issue and typically the remote begins to show indications of trouble long before it gives up completely. Make sure that the retainers are secure and do not have any corrosion on them. If they do, clean them with a suitable battery cleaning solution and a wire brush. Make sure you are using a button-cell battery that has identical in size, voltage and specifications as the original.

This could be a sign that your alternator isn't working properly. The alternator is what recharges your battery when you drive. A malfunctioning alternator can drain the battery fast and cause the warning light to turn on.

You can determine if the Hyundai is affected by a simple voltage test. If the battery is in good condition it's possible the issue is on the circuit board or a different part of the key fob. Press a small metal button tab on the front or back of the key fob to unplug it. Once you have removed the cover, put in a new CR2032 battery and make sure that all connections are in contact.

Reprogramming

Hyundai provides keyless entry on all of its models. This makes cruising around Littleton and Parker, CO, easier than ever. If you own an ignition key you can open and lock your car's doors and start the engine with the remote. But, it's not completely safe and a broken fob could cause issues. If your Hyundai keyfob doesn't work it is possible to reset it so that it works with your vehicle.

First, you need to remove the battery. Typically the button cell is housed inside an aluminum tab. If you remove the tab to replace the battery, make sure to use the same size and voltage as the original battery.

Once the battery is replaced, close up the tab and replace the retaining clips. Test the key fob again to make sure it still works.

If the key fob does not work, it may be time to contact an expert locksmith or dealer. A locksmith or dealer can cut a new key and remote for you, and can also program the key to work with your car. The cost for this service is typically cost-based, but it's worth it if your goal is to keep your Hyundai key fob running. They can also assist you to choose the right Hyundai key fob to meet your needs.