Are The Advances In Technology Making Fiat 500 Replacement Key Cost Better Or Worse?
Fiat 500 Replacement Key Fob
If your remote key fob has stopped working, it's time to replace the battery. If you do replace the battery but it doesn't work, then the problem could be elsewhere.
At United Locksmith, we specialize in the creation of new keys for classic cars. We have all the tools and accessories needed to perform this service.
Dead Coin Battery
A dead battery is the most common cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob is equipped with the battery of a coin-cell that will drain quickly in the event that it is not utilized frequently enough. If your remote starts to show signs of loss in range or stopped working and the battery is not working, it could be dead.
Metal clips keep the battery securely inside the key fob. If the clips aren't tight, they can create problems with the contact, which can stop your remote from receiving power. Utilizing a small screwdriver, push the clip that holds the retaining pin open to remove the battery, and replace it with a brand new one. Make sure to select an alternative battery that has the same kind of voltage, the same size and specifications as the original battery.
Water exposure can cause the key fob to corrode, or even become damaged. Even fiat keys in soapy, warm water can cause damage to the chip. Make sure your key fob is dry.
Water Damage
If your key fob isn't operating properly, it may be caused by water damage. Key fobs are fitted with rubber seals to protect them from being damaged by rain or a splash of water, however it is vital to keep your car keys out of the ocean, pool, and washing machine!
The key fob comes with an electronic chip inside that transmits a signal car's immobilizer system. This is what allows your 500 to start or lock, but in the event that the chip becomes wet, it will no longer work.
If you're looking to determine whether your key fob functioning, you can clean the internal electronics using isopropyl or electronic cleaner. However, it's better to purchase a new one from a dealership rather than trying to repair a key fob that was submerged in salt water.
A replacement fob could cost you a few dollars but it's far less expensive than paying to have your Fiat 500 towed to a dealership and fixed there! Plus, you can do it yourself in only a few steps. Just make sure you have the right battery type before you attempt to open your key fob. This task is much easier than it looks and you can find step-bystep instructions on the internet for nearly any car key fob.
Faulty Chip
The chip inside the key fob connects directly with the immobiliser on your car to ensure that your vehicle will start only when the correct keys are inserted. If the chip is damaged or corrupted in any way the car won't start.
Damage to the water or a dead battery are the most common causes of a faulty chip. It is best to delegate the task to a professional locksmith who can replace the chip quickly and at an affordable cost.
If your key fob does not function after being exposed to clean tap or rain water, remove the battery. Wipe down the electronic component with paper towels. If the key fob does not work it's likely to be a fried chip and will require replacement.
Some people will go to their dealer in order to get an entirely new Fiat fob. But, this can be expensive. If you are looking for a low-cost solution to get your Fiat key fob repaired, look no further than United Locksmith. We have the tools and knowledge required to repair your Fiat fob quickly and professionally. way.
Faulty Receiver Module
Fiat key fobs send an alert up 50 feet away to the vehicle, which will open and lock the doors (and start the vehicle in case of automatic transmissions). There are many reasons why the fob could stop working. These include a dead coin battery, water damage, worn buttons and a receiver module issue and signal interference or an electronic chip malfunctioning.
If the fob was in the pocket that has been subject to severe trauma (such as being dropped onto the floor, or washed in the washer) the fob might not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept signals from a genuine key and not any other.
It is necessary to replace the fob if this happens. A professional locksmith will handle the entire process of replacing your key including programming a new key for your 500. They can even provide an clone fob that performs the same as the original (and costs only one-third of the cost).