A How-To Guide For Kia Picanto Key Fob Replacement From Beginning To End
How to Replace a Kia Sportage Replacement Key
The key on many Kia models comes with the keyless entry feature built into. This key is similar to a remote control, and can be exchanged with an Kia dealer.
Key fobs may stop working due to a variety of reasons, including the battery of the coin is dead, worn buttons water damage, signal interference and a faulty receiver module. Here are some helpful tips on how to get your Kia Sportage replacement key to work again.
How to replace a smartkey or remote key?
If your Kia comes with an intelligent key, remote key push to start key or a regular non-transponder metal key, the battery in these keys will eventually need replacing. This is particularly relevant if your car displays a message indicating that the remote or smart key has low battery power.
It's a simple process. To replace the battery on the keyfob remove the mechanical key from the slit that is located at the back of the fob. Then, push the cover off. Inside the key fob, there will be the small screw that holds the battery in its place. Remove the old battery by removing the screw with a small screwdriver. Then insert the new one and close the slit inside the key fob.
Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to go on errands around Brandon.
Note: Certain key fobs (transponder chip or smart keys) may need to have their programming done. This requires a programming machine which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need record the key code number on the key code tag.
How to replace the battery
If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A weak battery could cause other issues, such as the check engine light coming on or the engine not cranking correctly. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires just some basic tools.
Be sure to turn off your vehicle and close all doors prior to starting. Find the small, metal or plastic piece that is located at the bottom of the key fob. Press it until the metal key falls out. Then, you can put the key into the handle of the door for the driver to unlock your car.
To replace the key fob's battery, take off the cover from the back and use a plastic pry bar tool to remove the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery to ensure that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or bending the contacts made of metal.
After the new battery has been installed and the key fob is turned on, turn it off and back on in the ignition several times until the door locks cycle. You can then test your Kia's key fob again to confirm that it's working as intended.
How do I replace a smart keys
Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The difference between these is that the smart key has tiny mechanical key blade that is hidden inside, while the standard fob does not. Both kinds of key fobs come with batteries that eventually will need to be replaced. It is a simple process that takes just two minutes.
Be sure to switch off your Kia and be on a level, well-lit surface before you begin. Keep in mind that the fob contains tiny parts that could be thrown off when you're not careful.
The first step is to find the small release button on the lower backside of your fob. It could be a circular or rectangular slot. After pressing kia keys replacement , it will be released and you can then open the key fob.
Once you have the key fob opened then you can take out the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. When you are done with the battery, you should be able to lock and unlock your car with your key fob - even if the engine isn't running!
How do you replace a broken mechanical key
The Kia key fob is a great option that lets us lock and unlock our car at the press of a button. Like all devices like a key fob, the Kia may have issues. Luckily, there are methods to resolve these issues and ensure that our key fobs are in good condition over the long haul.
A dead or low-quality battery is one of the most frequently encountered issues. The fob could be able to cease working or work intermittently. If this happens try replacing the battery with a new one.
If this doesn't solve the issue, try using a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.
When the new battery is installed, close and unlock the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and check that it's functioning correctly. Contact a dealer, or a locksmith to fix the issue when the fob still is not working. To avoid future lockouts, make sure you get an emergency key that can work in all of the trunk and door cylinders.