9 Signs You're A Fiat 500 Replacement Key Cost Expert

Fiat 500 Replacement Key Fob

It might be time to replace the battery if your 500 remote key fob isn't working. If you do replace the battery and it does not work, then the problem could be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic cars. We have the tools as well as the parts required for this type of service.

Dead Coin Battery

The most frequent reason that your Fiat 500 key fob will not unlock or lock the doors is due to a dead battery. The key fob is equipped with an in-built battery which will quickly drain when it isn't being frequently used. If your remote has started to show signs of loss of range, or has stopped functioning and the battery is not working, it could be dead.

Metal clips hold the battery in within the key fob. If the clips aren't secure, it could lead to contact issues, which could prevent your remote from receiving power. Make use of a flathead screwdriver to remove the retaining clip and remove the old battery. Choose a battery that is the same voltage, size, and specifications as the original.

The key fob can be damaged or corroded due to exposure to water. Even a brief bath in soapy water could cause damage to the electronic chip inside. Keep your key fob dry.

Water Damage

Water damage may be the reason behind your key fob not working properly. Key fobs come with rubber seals that stop them from being damaged by a light rain or splashes of water, but it is very important to keep your keys out of the pool, ocean, and washing machine!

The key fob contains an electronic chip inside it that transmits a signal car's immobilizer system. fiat key programming is what allows your 500 to start or lock, but if the chip gets wet, it can no longer work.

If you're interested in checking whether your key fob functioning it is possible to clean the internal electronics using isopropyl or an electronic cleaner. It is recommended to replace a key fob in the event that it's submerged in salt water rather than attempting to fix it yourself.

While a replacement fob could cost you a little bit of money, it is a lot cheaper than having to pay for your Fiat 500 to be towed to the dealer and repaired! Plus, you can do it yourself in several easy steps. Be sure to have the correct type of battery before attempting to open your keyfob. This task is far simpler than it appears and you can find step-bystep instructions on the internet for nearly any key fob for cars.

Faulty Chip

The chip inside the key fob communicates with the car's immobiliser unit to make sure the car is capable of starting when the correct key is used. If the chip is damaged or destroyed the car will not start no matter what you do.

Water damage or a dead cell battery are the most common reasons for defective chips. It is recommended to leave the repair to a professional locksmith who can repair the chip in a short time and at a an affordable cost.

If your key fob does not function after being exposed to clean tap or rain water take the battery off. Wipe down the electronic component with paper towels. If the key fob doesn't work it's probably to be a damaged chip and must be replaced.

A few people will visit their dealer when they require an entirely new Fiat fob. But, this can be costly. If you're looking for a low-cost solution to have your Fiat key fob fixed make sure you contact United Locksmith. We have all the equipment and know-how to fix your Fiat fob in a professional and timely way.

Faulty Receiver Module

Fiat key fobs send an electronic signal to the vehicle which will unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. There are several reasons why a fob could not function. This can be caused by a dead coin-battery, water damage, worn out buttons, a receiver issue, signal interference or an issue with the chip.

If the fob was placed in the pocket that has been subject to severe trauma (such as being dropped onto the floor, or washed in the washing machine) it might not be able to connect with the Body Control Module (BCM) of the car. The BCM is a security device that will only accept signals from genuine keys.

You will need to replace the fob if this occurs. A professional locksmith can handle all aspects of the key replacement procedure, including programming a new one for your 500. They can even provide you with a clone fob that works exactly like the original (and costs only less than the price).