7 Simple Changes That'll Make A Big Difference With Your Upvc Replacement Door Handles
UPVC Replacement Door Handles
Over time the handles on your doors will wear down and need to be changed. It is important to match the dimensions of the handles that were previously used when replacing them.
The three measurements to be inspected are the top screw's location the lever and key hole dimensions. Use the size guide to aid you.
Inline Lever/Lever
A lever or lever door handle is a contemporary handle that can be installed on new or replacement doors. This type of handle is available in many styles and finishes. A variety of manufacturers provide this handle including Avocet, ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The door handles made of uPVC/Composite are constructed of durable materials and are perfect for doors with multi-point locks that require a strong design. The handles are inline and operate off the same spindle and screw fixings, so they can be easily fitted to doors made of uPVC/Composite, either new or old.
The handle can be adjusted and angled to accommodate all users. The handle has been tested to 200,000 cycles. This will ensure the quality of the finish and the performance of the handle over time. The lever that springs is adjustable to accommodate a wide range of locks. This is especially useful in doors with smaller door frames where the cylinder is located further back. A shortened lever is also an excellent option for doors where the latch can be opened by a thumb turn located on the inside.
Lever Pad
A Lever Pad upvc door handle operates differently from lever-type handles found on most doors. The handle can use a single spindle (inline) or independently from each side by using two offset spindles or inline (pad). They are usually employed on UPVC double glazed doors and come in many variations & finishes.
The handles have been tested to the minimum of 200,000 cycles and are available in various finishes including White Silver, Chrome, & Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high degree of durability and performance for its intended use.
All of the UPVC lever pad designs come with a spindle and screws that allow them to be put on any new or existing uPVC door. The backplate fixing centres of 211mm allow for a wider handle, which can often be a benefit when replacing a faulty or worn multi point door lock mechanism. The levers for these handles have a spring, which solves the problem of door handles that sag out of horizontal position when not in use.
When choosing the replacement UPVC handle and spindle, it is crucial to match the PZ dimensions of both the multipoint lock and the uPVC door. This measurement can also be called 'handle centre' or cylinder centres'. It is important to match the correct handles.
After you have determined the correct PZ size and the correct PZ size, you must make sure that the push and lever pads are designed to fit the American with Disabilities Act compliant handles that you need for your door. These are typically of a round or square design with an internal lever and an external push pad.
The majority of UPVC lever pads we sell are sprung, meaning that they return to their horizontal position when they are not in use, instead of hanging out and potentially sticking in the frame. This prevents draughts from entering the home. The majority of UPVC lever pad style handles come in both left and right handed versions which allows them to be put on either side of the doors.
Euro Cylinder
Cylinder locks are usually used on uPVC doors, but can be utilized on other types of door. Cylinder locks are operated by using a key that unlocks the cylinder's case. The case is then able to reveal pins that can be aligned to the pins in the lock, and permit them to turn the revolving camera, opening the door. Euro cylinders are available with up to six pins. Internal and external doors require different levels of security.
The choice of cylinder is essential. It is based on the amount of use your doors and handles will receive. For instance, doors that are external must be secured with an extra secure cylinder, whilst internal doors can be secured using an ordinary cylinder. Some cylinders have extra features that can improve security, like anti-drill or anti bump properties.
To ensure that the euro cylinder is the right size for your door, it should be measured correctly. The cylinder should be measured from the hole in the center of the fixing screw to the other end of the cylinder including the thumb turn if you have one. If you are unable measure it using the lock in its position, you can take it out of it. It is essential to avoid having a extension of the cylinder beyond the handle or escutcheon. This can make it susceptible to lock snapping attacks.
The design of many modern cylinders comes with anti-drilling as well as bump resistance features. These are designed to reduce the chance of attack by forcing cylinders to turn in a different direction. This helps stop the attack and protect your doors.
There are cylinders constructed to resist snapping. This is a more frequent type of attack on cylinders where the break line inside the lock is attacked using a special tool to snap off the front of the cylinder and allow the door to be opened. This is faster and less difficult than opening multipoint locks. It also leaves little evidence of a burglary, which could hinder an insurance claim.
upvc replacement door handles repairmywindowsanddoors is found inside the base plate of your door handle. It offers a spring-loaded solution to bring your multipoint lock handles back to their resting position after usage. There was a time when handles didn't have a spring built into them, and without it they tend to droop or 'drop' once the locking mechanism is disengaged. This simple feature is one of the most effective ways to fix this issue and is a great way to prevent your upvc doors from getting stuck in either closed or open position, as these aren't always simple to close manually.
These spring cassettes have been specifically designed for use with multipoint locks sprung They will not work with unsprung multipoint handles and you will need to have a bespoke hole cut into your backplate to allow these to fit (please look at the image for a technical diagram). These cassettes are a solution to broken or missing cassettes that are in the backplate of uPVC door handles. They are available as one unit. They come with a square cut out that is able to accommodate an 8mm shaft.
These spring cassettes are a fantastic value for money solution to the issue of your door handles sagging. These spring cassettes are easy to install and can extend the lifespan of your uPVC door. Contact us for more information on our wide range of uPVC accessories and spares. We are on hand to help and happy to provide expert advice.