20 Things That Only The Most Devoted Subaru Xv Replacement Key Fans Understand
How to Change a Subaru Spare Key
If you've lost your Subaru car key, contact a locksmith. Usually, they will cut new keys for you for less than the dealer.
Fob remote "push to start" intelligent keys or a simple metal key are the two main types of Subaru car keys. The Fob key is equipped with an embedded chip that must be reprogrammed.
Keyless Entry System
A key fob can be used to lock or unlock your Subaru from a distance and can also open the trunk or lift gate of your vehicle. These remotes make use of a keypad in your car to communicate with your vehicle's computer.
Subaru models come with a lesser known feature dubbed PIN Code Access. You can utilize a personalized number sequence to start and open your car. If you have a model newer than Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that came with this feature, consult your owner's guide to find out how to make use of it.
It's likely that the battery inside the key fob is dying. You can check the battery life of your key fob using the portable tester or multimeter that you have in your garage.
The next step is to take the key fob out of its case and inspect its transmitter circuit board. You'll see two or three sets of 8-digits. Note the first set so that you can recall it. After you've completed this, you can begin programming the key fob at home. The procedure for programming is different based on the model and year of your vehicle but it's usually easy enough to complete yourself.
Key Fobs
Subaru's latest models have key fobs which not only unlock doors, but also activate lights, lock the gas cap and even start the car. This last trick is particularly useful if you have ever found yourself at the gas station and your car wouldn't even start because the battery in the key fob is dead.
It doesn't matter if your Subaru is new or older you can be sure that the key fob is able to be replaced with minimal difficulty. Be aware that some more modern models, with their advanced technology, may require a visit to the dealer. With some effort and time, you can create your own replacement key fob.
Begin by looking at the transmitter circuit board inside your key fob (instructions for opening the case should be included in the owner's manual). It should have two or three serial numbers each one of which is 8 digits long. Write down the number that is the first in the series and keep it handy to refer to later.
Next, climb into the driver's seat. Close all the doors. Turn the key to start your vehicle and then switch off after ten revolutions. Press the lock button on the key fob and open the door to check that your doors are functioning properly. After that, close the door and take the key out of the ignition. You should hear the chime from your vehicle and indicate that the key fob is programmed.
Ignition System
If your Subaru keys aren't working as they should, it could be because the key battery is dead. If you know how, you could replace the battery in your key fob yourself. A replacement battery is not expensive and relatively easy to locate. If the key fob doesn't respond to your commands it could be a different problem. To get a spare, it's best to visit an authorized dealer. They'll make sure that the key is genuine Subaru key that's under warranty. It will also be programmed to your vehicle. This is a lot safer and easier than buying an aftermarket key from a company on the internet.
The dealer will also cut a key for you if you give them your VIN number and as evidence of ownership. This information is used to identify the replacement key so that it is accepted by your immobilizer. This process is more involved than cutting a new one, and dealers will typically charge more for this service.
Once the new key is programmed it will be able to change it over to your existing key. You'll have only five seconds to insert the second key, so it's important to keep a working key on hand. You can take the key off after the security light stopped flashing and you can test it.
Battery Replacement
Subaru fobs are very beneficial because they can switch on the sunroof and power windows in your vehicle with just one button press. The battery inside your Subaru fob isn't designed to last forever, and it will have to be replaced eventually. This short guide from Capitol Subaru will help you to replace the battery on your own.
To begin you'll need to locate the tiny crevice inside the seam that separates the back and front of your key fob. With a small screwdriver, you can break the seam open and reveal a small compartment that houses the battery. Insert the new battery and ensure it's facing in the correct direction. Remove the old one. Once you've assembled everything and you are ready to use the new key fob for locking or unlocking your vehicle.
subaru car key replacement should always have a spare set of keys, particularly if yours is broken or has been lost. A new key can be found at your local auto dealer or you can get one made by an locksmith. It is important to ensure that your key fob works efficiently as soon as you can so that you can safely drive.