15 Top Pinterest Boards Of All Time About Door Lock Change
How to Do a Door Lock Change
Changing your door lock is an easy and inexpensive method to increase the security of your home. The process is not for all. It requires a certain amount of patience and skill.
The cylinder is contained within the knob's body. The cylinder recognizes the key once it's put into the lock.
Remove the old lock
The first step is to remove the old lock. This is a relatively easy procedure, but there are some things to be aware of. Make sure that the new lock fits the door. This will ensure that it fits securely, and doesn't leave a gap at the deadbolt or latch.
After you have removed the latch plate look for two screws or bolts on the inside of the casing that hold the casing and the halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock from the door. If you have a mortise locking system there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing the screw using a screwdriver.
You must also remove the latch and deadbolt plug from the hole in the door jamb. Install the new lock. If you are replacing a mortise lock, you must also measure the distance between the lock case and the door's edge to ensure that the new lock will be able to fit.
It is possible to replace your lock for various reasons, including the possibility that someone else holds the key or if you've a new roommate. You can save money by deciding to remove the lock yourself, instead of hiring for a professional. It's much easier than most people imagine and can be accomplished in a matter of a few minutes.
Start by getting rid of the trim and handle from the door. With a flat screwdriver remove the trim. You should be able to twist off the majority of it and in certain cases the handles could come off entirely. The next step is to search for a pinhole on the inside of the handle and insert straightened clips into it. This will trigger the release mechanism, which allows you to remove the handle. Then, look for another small tab on the interior of the lock, and press it with a flat screwdriver. After the spindle has been removed, you are able to remove the cylinder and the housing.
The choice of a new locking system
When it comes to choosing the right lock for your home there are a lot of options. Take a look at various types of locks and find one that matches the style of your door. Consider the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole that runs along the edge of the door frame). Also, make sure to choose a lock that will accommodate the door's thickness as well as swing.
The American National Standards Institute and BHMA have graded the majority of locks for doors to give you an idea of their strength and the difficulty to pick them up or disable them. A grade 3 lock may be a good choice for a tranquil suburban apartment complex, whereas a grade 1 lock might be more able to withstand the traffic near a busy storefront on a busy city street.
Most smart door locks need a digital code to open. If you're concerned about hacking or other security concerns you should consult a professional locksmith or your local police department to get advice.
Replacing the cylinder
If your door lock cylinder is broken or damaged you can repair it within a matter of minutes using a simple DIY project. The trick is to select the right cylinder, and follow the instructions that come with it. First, you must remove the handle or knob if it is present. Then with a screwdriver take off the trim around the lock cylinder. Once the trim is removed, you can reach the screws that keep the cylinder in place and remove them using the flat-head screwdriver. The cylinder is then gently pulled away from the door.
Be sure to measure the length of the new cylinder before installing it. With a tape measure, determine the distance between the cylinder's center and the left and right sides. Then, you can purchase another cylinder that has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside.
Insert the replacement cylinder in the door and then turn the key. This will align the cylinder with your carrier which is located usually on the outside of your lock. After that, you can loosen the set screw that should be just a few turns inside the head. If there is a screw on the outside of the case that is holding the door, you will have to loosen it.
You can replace the cylinder that was used to lock your old lock with the new one by inserting it into the case and then tightening the set screws. You must also install the piece that connects the cylinder to the lock indicator stem, which you can do by pulling out three small tabs on back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. You should then reinstall the strike plate and latch plate, as well as the retaining rings fixed to the top of the lock cylinder.
Installing a new lock
Start by measuring the door's width if you are replacing a lock that is already in use. Most locksets for residential use are designed for a door thickness of 1 3/8 to 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require an extra thick door kit. This will require longer screws as well as an extended spindle extension or the tail piece for door knobs.
The majority of locks come with a detailed instruction manual to guide you through the installation of the new hardware. Before you begin, read the instructions to make sure you've followed the steps. The guide will also give you an idea of the level of expertise required to accomplish the task. You may want to seek out a friend who has experience changing locks for assistance if you are changing a lock the first time.
Before installing the new lock it's a good idea to cover the holes with tape the old hardware. This will prevent the screws from slipping through the holes and will also protect any tiles you might have installed. It will also prevent any potential damage from rust, dirt, and grime. upvc window lock mechanism replacement www.repairmywindowsanddoors.co.uk includes the masking strip or gaffer tape, however you can make use of any tape you have.
After taking off the screws that connect the lock's interior to its exterior and take the lock off immediately. It's crucial to do this swiftly to avoid the lock from accidentally closing itself and harming the mechanism.
If your new lock is equipped with an internal latch bolt, insert the new latch bolt into its upper cross bore. Make sure you put it in the right position, which will be marked by an arrow. Then, you can screw the latch plate onto the bolt.
Screw the deadbolt into the jamb on the door. Test the deadbolt by throwing it a few times to verify that it extends all the way through the strike plate and is fully secured. Follow the directions included with your electronic smart lock to program it. This involves downloading an app and registering your e-mail address, confirming your identity and connecting to the wireless network to add your device.