15 Top Change Door Lock Bloggers You Need To Follow
Reasons to Change Door Lock
You can change your door lock for many reasons, from improving the security of your house to redecorating the entryway. You may also need to change locks if your key is stuck in the lock or is difficult to turn.
DIY novices can easily alter their lock. Gather the materials needed to begin.
Take off the lock that was previously used.
Before installing a new lock it is important to take out the old one from the door. This step is especially important if you suspect that someone else has a key to your home. It's also a good idea after you've moved into a brand new house, had a break-in, or welcomed a roommate. It is easier than you think to complete and can be done in just a few minutes.
Begin by getting rid of the screws that attach the deadbolt faceplate on the frame of the door. You will need to take off the screws on both sides of the door in order to remove the faceplate. This will allow you to discover what's behind it and will provide you with a better understanding of what to do with the rest of the steps.
After removing the faceplate you will have to remove the bolt as well as the strike plate and strike plate. Remove the bolt from the door hole with the screwdriver. If the bolt is rusty, you may have to use a chisel to remove it. If you are using a chisel, you must be careful not to damage the door frame.
Before you take out the old lock, make sure that your new deadbolt and doorknob will fit into the holes in the door. The majority of hardware stores and big box stores offer different kinds of locks. They can help you find the right one for your requirements. If the lock you bought isn't the right one for your door.
Look for small depressions or notches in the handle and around the trim as you remove the old lock. If you can locate them, you can use straightened safety pins or a flat screwdriver to open the handle.
After the screw in the handle has been removed you can begin to remove the knob from its spindle. To do this find the set screw that is located on the base of the knob and loosen it. Next, you will need to remove the knob from the spindle. Finally, carefully remove the spindle from the door.
Install the new lock
It's a good idea to change the locks on your doors frequently particularly if you've experienced a burglary. It's simple, inexpensive and efficient to change the lock on your door. With a screwdriver and a few basic instructions most people can do it by themselves. Based on the situation you may want to learn how to rekey a door lock to ensure that you only have the key.
You'll need to buy a new lock with the same keyway as your current lock. Locksmiths are usually able to change the lock's key for a fee but you can save money by doing this yourself. You can purchase a brand new lock at a hardware store or on the internet. A standard deadbolt will usually fit on all doors however, you'll have to measure the size of your door to make sure that it will fit.
Your new lock will often come with a template showing you how to install it on the door. The template can be used to drill the hole. It's a lot easier than having to measure every time. If the template does not exactly match your hole, bring it back to the shop and get another one.
When you install the new lock, you must ensure that it is placed on the right side of the door. Examine the latch. It should be marked with "up" or similar. Make sure that the latch is sitting correctly on the latch plate, then secure it with the screws supplied.
If you're replacing a door knob lock it is also essential to be aware of the type of lock you're using. Most knob locks are left-handed but there are some that are right-handed. If you're not careful, you may put the knob on the wrong side of the door, which could make it impossible to lock it from either the inside or the outside.
When you're done checking the new lock to make sure it's working. You should be able both to lock and unlock the door using a key from the inside as well as the outside. If you are not satisfied with the result, you can contact an expert locksmith to repair it.
Test the lock
A lock that does not open is a nuisance but it can also put the safety of your family at risk. It's easy to fix the majority of door lock issues by tackling the issue and lubrication. Verify that the key has been correctly cut, and that the lock assembly isn't loose or dirty. If this doesn't solve the issue Try lubricating the door lock actuator with graphite powdered.
Then, make sure that the door lock switch, the wiring harnesses, and the actuator connector are all working properly. Check the wiring diagram or manual to determine the color code and function of each door lock switch wire. Use a digital meter, or test light to determine if the actuator is receiving power and ground whenever the switches are turned on. If you observe an electric voltage switch on each switch's activation, it means the switches are working and it's most likely the actuator that requires to be replaced.
If the switch appears to work however the actuator does not move when you turn the knob, it could be an issue with the actuator cylinder itself. The actuator cylinder is loaded with spring pins that prevent the cylinder from turning until the key is placed in and moves the pins upwards to match the key's height in the location. The cylinder will then begin to turn opening the lock body and opening the handle latch.
If the door lock actuator is inoperable, you can remove the switch and wires from the actuator with a small screwdriver to release the locking bolt and remove the plastic cover that holds the electrical connector. After that, disconnect the door lock actuator and let it fall. Then, you should be able identify and remove the two 10mm bolts holding the actuator in position. After the actuator is removed, you can disconnect the black electrical connector.
Replace the key
If your deadbolt that is keyed or door knob is not working, you will have to rekey it or replace it. This is not difficult and can save you money. But, prior to doing this it is an excellent idea to have a locksmith look over the locks and check them for any issues. This will give you peace of assurance that your home is secure and safe.
Remove the exterior faceplate of the doorknob/deadbolt. There may be screws that are holding it in place, if then use a screwdriver loosen them and pull the faceplate out. Then, take off the interior faceplate using a screwdriver that has a flat head. Once you have removed your faceplate, you are able to remove the bolt and screw from the lock cylinder.
A locksmith can decide if you need to replace or rekey the lock. click here! can also offer advice on the best security measures for your home. They can also make any needed modifications to the door and frame to ensure that it is a perfect fit. They will also provide the guarantee for their work.
You need to purchase a new lock key before you can rekey it. It is essential to use the lock key that fits snugly. A key that is not properly fitted could cause damage to the mechanism's internal mechanisms and prevent it from working. To determine the size of a key, insert it into the lock. If the key is completely against the plug then it's the right size. If the pins extend from the top of plug the plug, then they're too long.
You may need to replace your door lock for a variety of reasons, including:
Rekeying locks is a cheaper option than replacing it if you are moving into the home of a previous owner or if keys have gone missing. It's also less expensive than a full replacement. Rekeying a lock that is already in use may not be feasible in certain situations. If the lock has been damaged or jammed repeatedly, for example, it may be time to replace it.