15 Things You Didn't Know About Ghost Immobiliser Install
Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for CAN buses. It's discreet, doesn't use LED indications or key fobs and is hidden within the vehicle's wiring.
It also permits the user to disable the system temporarily through Transport Mode to use it when they are renting out their vehicle. This guide will guide you through the process of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle from hacking, key cloning and relay attacks. The system is linked directly to the ECU of your vehicle and protected by a pin code you set. It is not detected by thieves using diagnostic scanners and other modern methods. It cannot be disabled by cutting circuits.
The system is easy to use, but it's essential to use a an expert installation to ensure a clean and secure connection to your vehicle's ECU. Installers approved by Thatcham can assist with the installation and programing of your Ghost system. They can also recommend a tracking system or alarm to complement your vehicle's security package.
First, the installer must disconnect the battery to prevent accidental airbag deployment or short circuits. After this is completed, the installer can safely begin work. Basic hand tools can be used for precise connections. A multimeter is useful to check electrical values. Insulation tape and cable ties are also essential for protecting connections and keeping wiring tidy. Lastly, the user manual offers specific instructions specifically tailored to your Ghost Immobiliser model.
During the installation, it is important to choose the right grounding location that is free of paint and debris. The installer should also make sure the immobiliser's CAN H and CAN L wires are connected to the correct ports on your vehicle's ECU. The wires can be plugged into or soldered based on the model. To ensure a reliable and long-lasting connection, it is recommended that you use a high-quality plug.
Once the install is complete Once the installation is completed, the customer can enable after the installation is complete, the customer can activate Transport Mode. This allows the vehicle to be used by valet parking or mechanics without needing to know the pin code. The customer must press the icon for service on the dashboard five times in 2 seconds. After that the system will verify with 5 indication signals.
The Autowatch Ghost 2 immobiliser is TASSA approved and a highly efficient immobiliser. It's a smart choice for anyone who frequently rents their vehicle on platforms such as Turo. Having an immobiliser can also lower insurance costs since it greatly reduces the chance of theft.
Getting Started
If you are seeking a solution to safeguard your vehicle from theft, you can't go wrong with an autowatch ghost immobiliser. The device protects your vehicle from being started even when a criminal steals or copies the key. It is possible because of its advanced technology that stops the engine from starting until the correct PIN code has been entered.
The device is connected to the vehicle's bus network CAN and allows direct communication with the ECU. It uses existing buttons on the dashboard and the steering wheel to create a unique sequence that only you can identify and makes it impossible for someone else to start your vehicle. This is the ultimate security system that will safeguard your car's pride and joy, keeping its value intact when you want to sell it in the future.
Installing a ghost immobiliser can be a simple process, but it is important to follow the directions carefully to avoid electrical issues and system malfunctions. First, you must locate a power supply of 12V and a suitable grounding for the chassis of your car. After that, you can begin connecting the wires to the immobiliser. Use high-quality connectors and soldering techniques for a secure connection. Insulate the connections using heat shrink tubing or insulation tape, as well as other materials to prevent electrical short circuits.
After the wires have been connected, you can reconnect the battery and turn on the engine to test the immobiliser's functionality. After you've verified that everything is working correctly, you can install the immobiliser in a secure location in the vehicle. Be sure to cover it in a secure manner to prevent any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified, which means that it complies with the highest standards of security and is a great protection against car thieves. It offers superior protection against key cloning, hacking and relay attacks, and it isn't able to be disabled unless you know the code. It is also simple to use and can be put into a service valet mode so that your automobile is not activated when you take it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to deter theft of vehicles. It connects directly to the vehicle's CAN bus network and communicates with the ECU and ECU, making it a virtually undetectable addition to your vehicle. Unlike other aftermarket systems that require the removal of circuit components the Ghost Immobiliser won't interfere with any of the factory settings for your vehicle.
It's also undetectable to thieves using diagnostic scanners. The system doesn't transmit or receive radio frequency signals but instead uses CAN data for communication with your ECU. It doesn't even require any modifications to your current key fobs.
Enter your disarm sequence (either two or one buttons) and then switch on the ignition of your vehicle to use Ghost Immobiliser. The indicator will flash twice to confirm that you've entered the correct code. You can now start your vehicle and drive safely.
Once installed, the Ghost Immobiliser guards your vehicle from hacking or key cloning while also protecting its value. If you ever need to surrender your vehicle for service or valet parking, the Ghost Immobiliser can be temporarily disabled in Transport Mode.
To complete a Ghost Immobiliser installation, you'll have to find a source of constant power (12V) and a grounding point. Make sure that both are well-insulated and safe to touch. Cable ties are also suggested to secure the wires. This reduces the chance of theft by potential thieves. Make sure you double-check the position of these points to avoid making mistakes, and mark them with the help of tape or a label. Verify all connections for signs that they're wearing out. Make sure all connections are in place, and are properly protected. Make sure to test your Ghost Immobiliser after installation has been completed. This will make sure that the unit is working correctly and that all connections and insulation are secure. Be sure to fix any issues as soon as they arise.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge vehicle security system that is integrated into your car's ECU to block the engine from starting without authorization. thekeylab.co.uk cutting-edge technology protects your vehicle from hacking and key cloning along with other methods employed by thieves to steal cars. The Ghost also works in conjunction with existing alarm and tracking systems to provide the most complete protection for your vehicle. The Ghost's unparalleled features, paired with its subtle design makes it a sought-after choice for car enthusiasts and security conscious drivers.
It is important to follow the procedures for installation to ensure a proper integration of Ghost Immobiliser. Consult the wiring diagram of the vehicle as it will aid you in locating and connecting the wires. You'll need to determine the grounding and power sources. Once you've found them then you'll be required to mark them so that they're easy to identify during the installation process. It's essential to use high-quality materials and tools. Basic hand tools can assist to make precise connections, while a multimeter will confirm electrical values and guarantee safety. Cable ties and insulation tape will help keep all connections tidy and neat. Additionally, a user's manual will provide specific guidance specifically tailored to your Ghost model.
Before proceeding with the installation it is essential to test the system by entering the PIN code and then starting the vehicle. This step will confirm the immobiliser functions as intended and stop unauthorised vehicle starts. It is recommended to complete this routinely as part of your regular inspections of your vehicle to ensure that the system is always functioning properly.
After the installation is completed, you are now able to start driving your car with confidence. The Ghost will safeguard your pride and joy from would-be car thieves. It will ensure that no one is able to drive away with your vehicle if they do not have the correct PIN code. The Ghost can be linked to an approved Thatcham tracker, which detects attempts at theft or tampering. This allows you to track your vehicle if it is stolen.
The Ghost can be used on a wide range of vehicles and is compatible with the majority of major manufacturers. Monty's Locksmith can help you secure your vehicle with this cutting edge device. Contact us today to learn more about our services and installation options. We are a TASSA registered installer, which guarantees we follow strict standards for installing our products. This assures customers as well as insurance companies and law enforcement agencies that installations are carried out safely and properly.