15 Best Change Door Lock Bloggers You Should Follow
Reasons to Change Door Lock
You can change your door lock for a variety of reasons, from increasing the security of your home to re-decorating your entryway. It is possible to replace locks when your key becomes stuck or is difficult to turn.
DIY novices can easily change their locks. To start, gather the required materials.
Take off the lock that was previously used.
The removal of the lock that was previously installed from the door is a necessary step before installing the new one. This step is especially important if you suspect that someone else has a key to your home. It is also a good idea if you have moved into a new house that was burglarized, or had a roommate move in. It's much easier than you think and can be completed in just a few minutes.
Begin by getting rid of the screws that attach the deadbolt faceplate onto the door frame. You'll have to take off the screws on both sides of the door to remove the faceplate. This will let you observe what's behind it and give you a better understanding of how to proceed with the rest of the steps.
Once you have removed the old faceplate, then you have to remove the bolt and strike plate. Remove the bolt from the door hole with the screwdriver. If the bolt is rusted, you may need to use a chisel and smash it. If you are using a chisel, be careful not to scratch the door frame.
Make sure your new deadbolt, doorknob and lock will fit into the holes already in the door before you take out the old one. A lot of hardware stores and big box stores carry a variety of locks and can assist you in selecting the best one. If the lock you bought doesn't match your door, send it back and ask for assistance.
Find small depressions or notches in the handle and around the trim when you remove the old lock. If you can locate them, slide a straightened safety pin or a flat screwdriver into them to loosen the handle and expose screws underneath.
After taking the screw off the handle, you can begin removing the knob. To do this find the set screw at the knob's base and loosen it. The next step is to remove the knob from the spindle. Finally, carefully remove the spindle from the door.
Install the new lock
It's a great idea to change the locks on your doors frequently particularly if you've been the victim of a break-in. It's simple, inexpensive and efficient to change the lock on your door. With a screwdriver and a few basic instructions the majority of people can do it by themselves. You may also want to learn how to change the lock's key to ensure that only you have the key.
To begin the process, you'll must purchase an additional lock that matches the keyway on your existing lock. Most locksmiths will change the lock's key at a cost but you can save money by doing this yourself. You can buy the new lock at hardware stores or on the internet. Standard deadbolts will fit most doors. However, you will have to measure your door to ensure that it fits.
The lock you buy will typically come with a template showing how to put it on the door. You can use this as a reference when drilling the hole, which is a lot easier than measuring every time. If the template doesn't align with your hole, you can take it back to the store and purchase a new one.
You must install the new lock on the right-hand side of the door. You can confirm this by checking the latch, which must be marked "up" or something similar. Make sure that the latch is properly placed in the latch plate, then secure it using the screws provided.
When replacing the knob lock be sure to be aware of its handing. Some knob locks are right-handed. If you're not careful, you could install the knob on the wrong side of the door, which will prevent you from locking it from either the inside or the outside.
You should test the new lock after you have completed. You should be capable of locking the door from both the inside and the outside, as well as unlock it with keys. If you're not happy with the outcome, you can contact a locksmith to repair the issue.
Test the lock
A door lock that will not unlock can be annoying however, it could also put the safety of your family at risk. RepairMyWindowsAndDoors 's not difficult to fix most issues with door locks by doing a bit of troubleshooting and lubrication. Verify that the key has been properly cut, and that the lock assembly is not dirty or loose. If this doesn't resolve the issue Try lubricating the door lock actuator using graphite powdered.
Make sure that the doorlock switch, wiring harnesses, and actuator connectors are all working correctly. Refer to the wiring diagram or manual to determine the color code and function of each wire of the door lock switch. Use a digital meter or test light to verify that the actuator is receiving power and is grounded when the switches are activated. If you see a voltage toggle with every switch activation, this means the switches are working and it's most likely the actuator that requires to be replaced.
If the switch appears to work, but the actuator doesn't move when you turn the knob it could be a problem with the actuator itself. The actuator cylinder has spring-loaded pins that prevent the cylinder from moving until the key is inserted, which moves the pins upwards to match the height of the key at the point of entry. Eventually, this causes the cylinder to spin and let the lock body open, allowing the handle to latch.
If the door lock actuator still not functioning, you can remove it by using a small screwdriver. It is necessary to release the bolt that locks it first and then remove the plastic cover that holds the electrical connector. Then disconnect the door lock actuator, and let it fall. Then you should be able to identify and take off the two bolts of 10mm which hold the actuator in place. After the actuator is removed, you can disconnect the black electrical connector.
Replace the key
If your deadbolt that is keyed or door knob isn't working, you'll have to reset it or replace it. It's not hard to do this yourself and can save you some money. It is best to have an expert locksmith examine the locks for any problems prior to starting. This will give you peace of mind that your home is secure and secure.
To begin, take off the faceplate on the outside from the doorknob or deadbolt. If there are screws holding the faceplate in place, use a screwdriver and remove it. Then, use a flat head screwdriver to take off the interior faceplate. After removing the faceplate you can remove the bolt and screw from the lock cylinder.
A locksmith can assist you determine if your lock requires replacement or replaced with a new key. They can also advise you on the best security options for your home. They can also make the necessary modifications to your door and frame for a perfect fit. They also provide a warranty on their work.
If you decide to rekey the lock you must first purchase a new key for it. It is important to use the lock key that is fitted snugly. A key that is not the right size may harm the internal mechanism of a lock and stop it from working. Insert the key into the lock to test its size. If the key fits flush against the plug, then it's the correct size. If the pins extend from the top of the plug and are not a good fit, they're too long.
You may want to change your door lock for many reasons, including:
If you're moving into a former owner's home or if you have lost keys, rekeying the lock can be a more affordable alternative than replacing it. It's also less expensive than a full replacement. Rekeying a lock that is already in use may not be feasible in certain circumstances. For instance, if your lock is damaged or jammed repeatedly, it's likely time to replace it.