14 Companies Doing An Excellent Job At Door Lock Change
How to Do a Door Lock Change
Door lock change is a simple and affordable way to improve your home security. However, this procedure is not for everyone. It requires a certain amount of patience and expertise.
It is necessary to replace the cylinder, which is located within the knob's body. The cylinder is responsible for recognizing the key when it is put into the lock.
Remove the old lock
The first step to replace the door lock is to take out the old one. This is a relatively easy procedure, but there are some things to be aware of. First, make sure that the lock you choose to install is the correct size for the door you have. This will ensure that it fits properly and does not create a gap around the latch or deadbolt plug.
After you have removed the latch plate, you will be required to search for two bolts or screws in the casing's interior which are holding the casing together with the two halves of the lock. Unscrew these with a screwdriver and then take the lock out of the door. If you have a mortise locking mechanism, there is a set screw that binds the handle to the spindle. Use a screwdriver to unscrew the screw, and then take out the doorknobs.
Remove the deadbolt and latch plug from your door jamb. Install your new lock. If you're replacing a mortise you must measure the distance between your lock's case and your door's edge to ensure that the new lock is a good fit.
You may want to replace your lock for a variety reasons, such as when you suspect that someone else holds the key or you've got a new roommate. In any case, you can save money by removing the lock yourself rather than paying a professional to do it. It's easier than many people imagine and can be completed in just a few minutes.
Start by getting rid of the trim and handle from the door. Then, you can pry the trim loose using a screwdriver that is flat. You should be able to twist off the majority of it. In some instances you might be able to remove the handles completely. Then, check the handle for a tiny pinhole on the inside. Then insert upvc window lock repairs near me straightened paper clip into it. This will trigger the release mechanism, which allows you to take off the handle. Next, examine the interior side of the lock for another small tab that you can press using a flat screwdriver. Once the spindle is removed, you can take off the cylinder and housing.
The choice of a new locking system
When it comes time to pick a new lock there are a lot of options. Consider different kinds of locks, and select one that fits the style of your door. Take into consideration the backset which is the distance between the edge and the middle of the hole in the lock. Also consider the cross bore, a small hole in the middle of your door frame. Also, make sure to select a lock that is able to fit the door thickness and swing.
The American National Standards Institute and BHMA have graded most locks for doors to give you an idea of their durability and how difficult it is to pick them or disable them. A grade 3 lock might be the best choice for a peaceful suburban apartment complex, whereas the grade 1 lock may be more able to withstand the traffic near a busy storefront on a busy city street.
Most smart door locks require digital code to open. If you are worried about hacking, or any other security issues, talk to a professional locksmith.
Replacing the cylinder
If your door lock's cylinder is broken or damaged, you can replace it within a matter of minutes using a simple DIY project. It is crucial to choose the appropriate cylinder and follow all instructions. The first step is to take off the handle or knob in the event that one is present, then unscrew the trim that is attached to the base of the lock cylinder by using a screwdriver. Once the trim is removed, you can reach the screws that hold the cylinder in place and remove them with the flat-head screwdriver. The cylinder can then be gently removed from the door.
Be sure to measure the length of the new cylinder prior to installing it. Take a measurement of the distance from the center to the left and right sides of the cylinder with the aid of a tape measure. Buy a new cylinder that has the same measurements. This will help prevent cylinder snapping, which can occur when the door is kicked out or when the key sticks inside.
Place the replacement cylinder inside the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is typically located on the outside of the lock. Then, loosen the set screw, which should be a couple of turns in the head. You will also need to loosen the screw at the door's edge that fastens the case, in the event that there is one.
After taking the lock cylinder out and replacing it with a new lock by sliding the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder to the lock indicator stem that you can do by removing three tabs on the back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you need to put back in the strike plate and latch plate, as well as the retaining ring that is connected to the top of the lock the cylinder.
Installing the new lock
Start by measuring the door's width if are replacing a lock that is already in use. Most locksets for residential use are designed to fit a door thickness of 1 3/8 - 3/4 inch. If your door is more than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This would include longer screws, or an extended spindle extension or tail piece for door knobs.
The majority of locks come with a detailed installation guide to aid you. Take the time to read the instructions before beginning the process to ensure that you've followed all the steps. The guide will give you a good idea of how much skill is required to finish the task. If you're changing a lock for the first time, you may consider asking a more experienced friend for assistance.
Before installing the new lock it's a good idea to cover the openings with tape the old hardware. This will stop the screws from slipping through the holes and will also protect any tiles you have installed. This will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes the masking strip or gaffer tape. However, you can use any tape you have.
Once you've removed the screws holding the interior half of the lock section to the outside side immediately, pull it back. It's important to do this quickly to avoid the lock from accidentally closing itself and damage the mechanism.
If your new lock is equipped with an latch bolt, install the new bolt into its upper cross bore. Make sure that you place it in the proper position, which is indicated by an arrow. Then, place the latch plate on top of the bolt and screw it into place.
Screw the deadbolt into the jamb of the door. Check the deadbolt several times by throwing it to ensure it is extending into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying your identity, and connecting to the wireless network in order to add your device.