13 Things About Fiat Panda Key Fob Replacement You May Not Have Considered

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 makes it easy to open doors and start your car. There are a myriad of reasons the fob could stop functioning. This could be due to a dead coin battery damaged receiver module, water damage issues, and interfering.

This listing is for an NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason the 500 key fob won't work is an inactive battery. Modern key fobs have a very limited operating range, and should be within some feet of the car to operate. If you're far from your car and press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) with a new battery of a trusted brand like Panasonic Duracell or Energizer. They are available at your local hardware store or online.

After you've replaced the battery of your coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switches.

If your fob's key doesn't work even after replacing the battery, there may be water damage which prevents it from interacting with the module inside your vehicle. Water damage can happen in a variety of ways, ranging from a light splash to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture out. If this fails, you'll require your fob to be reset by an auto locksmith or a dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to become shorted and eventually end up dying. Getting the fob wet is not an ideal choice, but if you drop it in a cup of water or fail to take it out of your pants pocket before running the washer and you don't have a chance, don't give in.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Test the fob next to determine if it's functioning. If the key does not function, it may need to be reprogrammed. This is typically done by a dealer or professional auto locksmith.

If the key is a newer model and hasn't been programmed to your vehicle It is likely that it needs to be replaced completely. A professional automotive locksmith can complete this simple process. The locksmith will have to cut the key to match the ignition in your vehicle. The locksmith will also need to reprogram your fob in the car's system. This is a fast and cost-effective process that is usually completed in the same day.

Receiver Module Issues

The 500 key fob you have may stop working because it is out of range. The remote typically has 30 feet of range or less and if it's far from your car, it will not respond to your commands. This can easily be resolved by moving closer to your vehicle until it starts responding.

If your fob doesn't work after you replace the coin battery, also called a "button", "watch" or "button", it could be due to an issue with the internal circuit board. Reprogramming the fob usually resolves this problem. You can find the procedure for most vehicles on YouTube or in the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they lose tension it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob could be out of connection with your vehicle as a result of hardware or software issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases, the software may also require reinstallation to your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be receiving or transmitting the signal due to interference. This can occur when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob might not work due to a bad connection with the buttons, water damage or damage to the internal chips.

If the key fob has stopped working one day in the middle of the night or after trying everything you can at home to resolve it e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module, located under the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computers. This could help the key fob to function again. If the issue persists, you should consult an expert technician. G28 Car Keys 'll be able determine the root of your issues.