12 Companies Are Leading The Way In Door Lock Change
How to Do a Door Lock Change
Change of the door lock is a quick and cheap method to increase your home's security. However, this procedure isn't for all. It requires a certain amount of patience and skill.
The cylinder is inside the knob's body. The cylinder is responsible for recognizing the key as it is put into the lock.
Take off the lock that was previously used.
The first step to replace the door lock is to get rid of the old lock. This is a relatively easy process, however there are a few things to be aware of. First, make sure that the lock you choose to install is the correct size for the door you have. This will ensure that it is securely fitted and won't create a gap around the latch or deadbolt.
After you have removed the latch plate, you will have to look for two screws or bolts on the inside of the casing which are holding the casing to the two halves of the lock. Take these screws off using a screwdriver and then pull the lock out of the door. If you have a mortise locking system, there is a set screw that binds the handle to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.
You must also take the deadbolt and latch plug from the hole in your door jamb. Then, you can put in your new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the door's edge to ensure that your new lock will fit.
Several reasons might prompt you to change your door lock, including being concerned that someone else may have the key or welcoming an incoming roommate. You can save money if you take the lock off yourself instead of hiring for a professional. It's much easier than most people imagine and can be completed in a matter of a few minutes.
Remove the trim and handle of your door. Then, you can pry the trim away with a flat screwdriver. It should be possible to pull off the majority of it. In certain cases you may be able to take off the handles completely. Next, examine the handle for a small pinhole on the interior side and insert a straightened paper clip into it. This will activate the release mechanism, which allows you to take off the handle. Then, look for another small tab in the interior of the lock and push it with a flat screwdriver. After the spindle has been removed, you can remove the cylinder and the housing.
The process of selecting a new lock
You have many options when it comes to choosing a new lock. Take a look at various types of locks, and find one that matches your door's style. Think about the backset which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, a tiny hole that is located at the edge of your door's frame. Choose a lock that fits the door thickness and the swing.
The American National Standards Institute and BHMA have graded all locks for doors to give you an idea of their longevity and the difficulty to pick them or disable them. A grade 3 lock could be the best choice for a peaceful rural apartment complex, while a grade 1 lock might be more able to withstand the traffic near a busy storefront on a busy city street.
Most smart door locks require a digital key code to open. If you are worried about hacking, or any other security concerns, consult an expert locksmith.
Replacing the cylinder
If the cylinder of your door lock is damaged or broken, you can replace it in a matter of minutes by completing a do-it-yourself project. It is important to select the appropriate cylinder and follow all instructions. First, you must remove the knob or handle if it is present. Then using a screwdriver take off the trim around the lock cylinder. Once the trim has been removed, you can access the screws that hold the cylinder in place and remove them using a flathead screwdriver. The cylinder can then be gently lifted out of the door.
Before you install the new cylinder, you must make sure that it is the right length for the door you are using. With a tape measure, measure the distance between the center of the cylinder and the right and left sides. Then, buy another cylinder that has the same measurements. This will prevent the cylinder from snapping, which could happen when the door is kicked out or when the key is stuck inside.
Once you have a suitable replacement cylinder, put it into the door and turn the key. replace window locks upvc RepairMyWindowsAndDoors will align the cylinder with the carriage which is located usually on the outside of the lock. After that, you can loosen the set screw that should be a couple of turns in the head. If there is a screw located on the edge of the case, which holds the door, you'll need to loosen it.
After taking the lock cylinder out, you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. You must also install the part that connects the cylinder with the stem of the lock indicator that you can do by pulling out three small tabs on the back of the cylinder using needle-nose pliers. Then, you can connect the smaller bracket to the back of the cylinder. Then, you need to put back in the strike plate and latch plate as well as the retaining ring connected to the top of the lock the cylinder.
Installing the new lock
Start by measuring the width of your door if you are replacing an existing lock. Most locksets for residential use are designed to fit a door thickness of 1 3/8 to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require a thicker door kit. This will include longer screws, or an extension for the spindle or a longer tail piece for door knobs.
The majority of locks come with a thorough installation guide to assist you. Take the time to read the instructions before starting the process to make sure that you are following all the steps. The manual will give you a good idea of the level of skill that is required to finish the task. You might want to ask a friend who has experience changing locks for help if you are changing locks for the first time.
It's a good idea to seal the openings of the old hardware before installing the new lock. This will stop screws from falling through the holes and will also protect any tiles you may have installed. This will also protect your tiles from damage caused by dirt, rust and grime. SECURAM Touch comes with a strip painter's tape that is intended to be used for this purpose, but you can also use gaffer's or masking tape if you have it available.
After taking off the screws that connect the lock's interior to the exterior then take the lock off immediately. It's crucial to do this quickly to avoid the lock from accidentally closing on itself and damage the mechanism.
Fit the new latch bolt in the upper cross bore of the new lock, if it has one. Be sure to put it in the right position that is usually indicated by an arrow on the faceplate. Then, you can screw the latch plate onto the bolt.
Screw the deadbolt to the jamb of the door. Test the deadbolt a few times by throwing it to make sure it extends into the strike plate. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an app, registering your e-mail address, verifying your identity and connecting to the wireless network in order to connect your device.