10 Things That Your Family Teach You About Saab 93 Key Fob
How to Replace a Saab 9-3 Key
The Saab 9-3 is a car that has a large amount of appeal for drivers. It has good visibility and an impressive performance engine. It has a very high safety rating.
However, it is important to make sure that you have at minimum two working keys for your vehicle. It is costly to replace a key in the event that you lose it.
How to Replace the Ignition Key in a Saab9-3
If the car key won't turn on, you need to replace it. saab car keys will teach you how to replace the ignition key on a Saab 9-3. You will need to replace the key, get a new reprogrammable cell, and then purchase a new casing for your key-fob.
Contrary to earlier models, modern Saab automobiles use a transponder on the key-fob instead physical metal key to unlock and start the vehicle. The issue with this is that the reprogrammable battery in the key-fob eventually wears out and not hold a charge anymore. This is particularly applicable if you are using the same key for the lock you have.
The good news is that the battery can be replaced easily by an experienced locksmith. You can also do it yourself if you have the appropriate tools and a bit of patience. The first step involves separating the key-fob. This is accomplished by inserting a flathead screwdriver into the slot located in middle of the case. The plastic is thin and it is susceptible to being damaged.
After the case has been opened and you are able to prepare the new key by combining the lower half of the key that was used previously with the transponder and banana on the new key. This will ensure that the new key is correctly paired to your CIM that can make a big difference when replacing the sole keys for your Saab 9-3.
How do I replace the ignition Key in a Saab 900
If you don't have two keys, you will need remove the steering wheel and dashboard for access to the ignition. Start by disconnecting your negative battery cable. Once the battery is disconnected, you can remove all the trim pieces and dashboard pieces that surround the steering wheel. Once the dash is taken off, you can push a screwdriver into the hole on the back of the ignition switch and pull it out.
The ignition cylinder is equipped with a key lock, which could stop the vehicle from starting if it doesn't have the key inside it. If the ignition switch of your 900 isn't working properly, check the key to determine if it's in the lock or is stuck in the barrel of ignition. You should also rotate your keys and keep them clean to prevent breaking.
Saab cars differ from other cars in the sense that they don't make use of traditional keys made of metal. Instead, the car can recognize the electronic signals generated by the key fob through a special chip in it.
If you lose your sole working key fob the dealer will charge you the most expensive dollar to replace the computer module (known as the CIM). We can reprogram the EEPROM on your existing computer and make it accept new keys, without the need for replacement. You'll save more than 50% on the dealer's cost! We call it the SAAB KEY PROGRAM. Find out more information about it here!
How to Replace the Ignition Key in the Saab9-5
The metal component of a traditional Saab key is easy to copy, and is not much of an impediment against vehicle theft. The real security is the electronic component of the key-fob, which has a chip inside that can recognize your vehicle when it's put into the ignition switch.
Saab has relied on the technology of this anti-theft system for over a decade. It's not as good as a physical lock on the door, but it does make the theft of your car much more difficult. This is why every Saab owner should always keep a spare key on hand.
Most new Saabs come with two keys right from the factory. However, you can upgrade them at an authorized dealer using a handheld computer called Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this is NG 9-3 cars, which have newer, more modern features that require a separate key-fob to utilize a different process.
If you lose all keys and the dealer replaces your CIM or TWICE modules, and charge you an additional fee for it. We can however reprogram the EEPROM on your computer and make it accept new keys, without having to replace the expensive modules.
How do I replace the ignition Key in the Saab XC90
If your SAAB 9-3 key fob begins having trouble turning the lock barrel, it may be time to replace it. Fortunately, the process is fairly simple and doesn't require you to visit an agent. Instead you can complete the process yourself at home, using just the help of a few tools.
The first step is to prepare the new key. Before you begin, turn off the anti-theft by placing blocks underneath your rear wheels and engaging your handbrake. After that, insert the key into the ignition and move it to the on position that activates the accessories but it doesn't start the engine. Repeat this procedure 5 times, then turn off the key on the "on" position.
You'll then need to purchase a new case for your key fob. You can find these at any auto parts shop, and they're typically very affordable. Depending on the model, you can even buy them without electronic components.
To open the case, put a flathead screwdriver in the slot located in the middle and gently work it. The case should split easily, and once you do, you'll have access to the internal electronics. Use a flathead screwdriver to gently pull out the electronic components.