10 Things That Your Family Teach You About Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 makes it easy to open doors and start your car. There are many reasons why the fob won't work. These include a dead coin battery or water damage, receiver module issues, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob being inoperative. Modern key fobs have a very limited range of operation, and must be within just a few feet of the vehicle to function. If you're far from your vehicle and hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can find them in your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The car will blink its parking lights and the key fob should be able to operate the lock and unlock buttons.

If your key fob still isn't working even after replacing the battery, there may be water damage which has prevented it from communicating with the module in your vehicle. Water damage can occur in a variety of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you suspect that your fob has been exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work your fob will probably require reprogramming by an experienced auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the circuit board of the fob which causes it to short out and eventually die. If you get the fob wet, it's not an option, but if you drop it into a cup of water or do not remember to take it out of your pocket before you run the washing machine, don't give up hope.

First remove the battery from the fob. Clean the electronic chip with isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob again to verify if it's functioning. If the key doesn't function, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and was not programmed to your vehicle It is likely that it needs to be replaced completely. A professional locksmith for automotive can do this job. The locksmith will have to cut the key to match the ignition in your vehicle. They'll also have to program the fob into your car's system. It's a simple and cost-effective process which can be completed within the next day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote has a range of 30 feet, so when you're too far from your vehicle it won't be able to respond to your commands. It is possible to solve this issue by moving the remote closer to your car until it responds.

If your fob isn't working after replacing the coin battery, also known as a "button", "watch" or "button", it could be a problem with the circuit board inside. In most cases, reprogramming the fob will resolve this problem. You can find directions on how to do this on the majority of automobiles by searching YouTube or reading the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, they could stop the battery from being properly seated and can cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software issues or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases, they may need to reinstall the program in your body control module as well.

Interference

Interference can also cause the key fob not to receive or transmit signals. This is possible when the key fob is close to the radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob may not work because of a problem to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

Fortunately, there's fiat key replacement to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will remove any residual electricity and restart the car's computers. This can help you the key fob to function again. If the issue persists, you should consult an expert technician. They can identify the root cause of any problems.