10 Things That Everyone Is Misinformed About The Word "Peugeot Keys."
Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to experienced auto locksmiths with the right tools and know-how. They can program and create keys faster and cheaper than a dealership.
If the key fob has stopped locking or unlocking your doors it is likely due to a dead coin battery. There are other reasons for the key to be malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the case, you'll have to utilize the backup starting method which is explained in the owner's manual to your vehicle.
The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. They have a limited lifespan. peugeot 3008 key programming 'll eventually fail when they aren't used enough.
There is an easy solution to this problem. Check the voltage of the battery with a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. If the battery has corroded it is crucial to clean its contacts. You can do this by lifting the rubber covers that cover both battery terminals and using a wire brush to remove any corroded areas of the battery. After that, you need to connect the positive pole cables to the negative.
Water Damage
If your 208 won't start and the battery has not failed, you should look at the spark plugs. It could be that they are overly filthy, making them unable to spark. This can be fixed easily by cleaning the spark plugs in a workshop.
Peugeot cars use transponder keys that is compatible with the car's immobiliser system. This ensures that only the correct key is able to start the engine. If the chip inside the Peugeot key is damaged then it won't send the correct signal to the vehicle.
Water damage is a typical reason for this issue. This is most common in colder climates, where the vehicle could have been exposed to snow or rain. In this case, you need to contact an experienced locksmith who will have the tools and equipment needed to change the key's programming. They will also have the latest technology and machinery needed to create the Peugeot smart key. The process should not take more than 15 minutes.
Faulty Battery Contacts
Peugeot replaced the transponder chips by introducing a new type that uses electronic components that are mounted on a circuit board. The new system is effective when it's fresh, however, over time, the circuit boards start to lose their effectiveness and cease working correctly.
This can stop the immobiliser chip activating, so your car won't start. If this is the case it's best to get in touch with a Peugeot specialist or locksmith.
A common issue is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith can replace the battery and cut a new blade for you, it's usually a simple fix.
Faulty Receiver Module
It could be that the receiver module is defective when your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a sudden rainstorm or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle.
The rubber seals on the key fob prevent water from reaching its electronic chip. However, prolonged exposure to water can penetrate these seals and damage the chip. Submerging the key fob into ocean water on the beach or throwing it into the water can be particularly damaging due to the high salt content.
If your Peugeot spare key fob isn't working You'll need the module replaced. This can only be completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys like other cars are protected by an immobilizer system. This requires the right programming to allow the car to start. It is for this reason that you should only rely on the Peugeot locksmith to create and program the replacement.
Computer on-board is not working properly
The on-board computer inside your Peugeot is responsible for a variety of the systems in your car, from power windows to the airbags. If something goes wrong with these systems, they will usually show a code that identifies the problem. This code will be stored in the system until the problem is fixed. This will often require the on-board computers to be replaced.
One of the most frequent causes of the airbag light flashing is loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, ageing or exposure to salt and moisture. This issue should be taken care of as soon as you can, because an airbag malfunctioning could be dangerous in the event in the event of an accident.
If your Peugeot is showing a card detected as not present error, the battery in the key fob may be weak or dead. This will prevent the key fob from sending a signal to disable your vehicle's immobilizer. Test this by pressing the unlock button on the fob's key, then trying to start your car. If this doesn't work, then the key battery will need replacing.