10 Things Everybody Hates About Car Key Button Repair
Car Key Button Repair
A broken car key button is frustrating. You might need to call an emergency locksmith service 24 hours a day to help or purchase a new remote.
But, you may be saving money by repairing a worn-out key fob instead of replacing it. This is especially true when the issue is due to the worn-out switch or defective contact.
Battery
If the buttons on your key fob aren't responding to pressing it, that could be a indication that the battery is dying or at the end of its life. Fortunately, replacing the battery is a simple task that you can complete by yourself rather than paying a locksmith or dealership to take care of it.
First look for the battery compartment. It is usually located on the back of the key fob. It might be hidden behind the cover, which slides out, or an access point which opens when you press the button. Once the compartment is exposed then you will find the small cell battery. It's usually the shape of the shape of a coin and is has a plus and the minus symbol. Remove the old battery and replace it with a brand new one. Make sure the plus and symbol are aligned correctly.
Close car key repair shop near me and snap the two halves of your key fob. Before closing the door make sure to align and snap the pieces in the correct position. To test that the buttons work properly, press any of them.
If your remote key fob stops functioning even after replacing the battery, it could be suffering from other issues that require a different form of repair. The fob's dropping into a pool of water can cause it to stop working. Alternatively, it might be suffering from an internal electrical problem or might need to be deprogrammed by an expert or locksmith. Try to figure out if the problem is related to your key fob using these other common automotive troubleshooting methods.
Switches
Based on the year and the model, there are a variety of types of switches that are used in the keyfob of your car. The older style keys have an embedded chip that can be seen in the case. The modern keys function by transmitting signals to your car. No matter what type of key, the keys' buttons can get worn down or damaged when used regularly. They can become difficult to press or unresponsive. If you attempt to force the button to function the button, it could cause damage and may even stop the key from starting your vehicle in the future.
If you are unable to get your key to function, try changing the batteries. If that doesn't help it may be necessary to clean the key's fob and re-adjust the switches. Because these tiny electronic switches spend a lot of time being tossed around, they are more likely to fail than the larger components of your key.
The switches feel rubbery and are coated with an electrical conductor. The film may fade over time. Luckily, they're also tiny and affordable to replace. The older ones are soldered to the circuit board, so you will need to carefully remove them without causing damage to other parts. You can then solder new ones into and reassemble the fob.
A good way to keep your car key fob from getting damaged is to avoid using it for longer than a couple of hours at a time and to keep it out of the way in visible locations in areas where it is visible. When you're not using your key, keep it in a secure location.
If the issue persists after you've cleaned your key fob, replaced the battery and tried to clean it, then you may need to consult a locksmith. A professional locksmith can test the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, change cases and more.
Outer Case
If the buttons can't move freely up and down the case, they may get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab does not work, it might be necessary to take off the case. If the contacts that the buttons touch aren't an ideal fit or are worn, adjusting them may be the only solution.
Rubber buttons be worn out over time. Rubber buttons can become hard to press as they stretch, and nails may cut them. This can cause the key to fail and, in this situation, it's time to get an entirely new case or buttons. This repair involves disassembling your remote, locating the buttons on the board, heating the solder and carefully remove them. The circuit board is soldered with new buttons. The case can be reassembled, and the horseshoe key blade piece can be attached. The new buttons should be snugly fitted into the case to keep them from falling out.
Inner Case
Since your key fob is likely be tossed around and could occasionally be pressed by accident and the buttons inside may get damaged or stuck over time. If your key fob isn't working while you are away from home, you can solve the issue quickly using metallic tape and punch holes. This will allow you to unlock doors but not start the car. This simple fix will enable you to safely make it back to your vehicle and finish your trip.