10 Quick Tips On Replacement Locks For Patio Doors
Replacement Locks For Patio Doors at Lowe's
Replacing your patio door lock can be an easy way to improve the security of your home. But, it is crucial to perform routine maintenance and install the lock correctly.
It is essential to know the type of patio door lock you are using to replace it with success. You can determine the type by observing the screw hole size and the type of face plate at the end.
Identifying Your Existing Lock
If you are considering purchasing a new hardware for your lock it is crucial to be aware of the differences between types of locks. This will assist you in locate the ideal replacement, and ensure that your home is safe and secure.
The most common lock is the cylindrical lock. It's also called a pin-and-tumbler lock. This type of lock makes use of a combination of top pins, bottom pins and springs to keep the key hole and plug secured. Cylinder locks come in many different sizes. It is crucial to determine the length and width of the cylinder you currently have before you purchase a new one.
To determine the size of the lock you have make use of a screwdriver to loosen the screws holding the cylinder and then carefully pull it out. Then, measure the distance between the outer edge of the cylinder and its inner edge and record the measurement in millimeters. You can then check this number against the measurements of the new lock you're planning on purchase. This will ensure that the new lock will fit into the door's lock hole.
Another method to determine the proper size of the lock you have is to test it by using the help of a key. If the key is able to slide easily into the cylinder it's the same size as the rekey kit you need. If the key doesn't slide into the cylinder, it is likely that the cylinder has different keyways and cannot be rekeyed to accept that type of key.
It is essential to follow the instructions supplied by the manufacturer that come with a kit for rekeying. Every kind of lock has specific installation requirements. It is also a good idea to spend the time to thoroughly test the new lock after installing it to make sure that it is working correctly and offers the highest level of security. You should also be aware of any additional features of your new lock, since they can impact its ease of use.
Take a measurement of the Width
A damaged patio door lock can lead to serious security concerns. It is crucial to regularly check your locks and replace them as required. This will ensure that they're functioning properly and are safe. It could be a good idea to avoid problems such as a damaged latch or keyway. Lowe's has replacement locks that will give your home the security it needs, whether your existing locks are damaged or worn out.
Before you purchase a new patio door lock, it's important to determine the dimensions of your existing one. This will give you an idea of what size to buy and avoid the risk of purchasing an unsuitable lock. To do this, you'll have to make two measurements in the length of the backset as well as the case depth. The former is the distance from the edge of the lock's face to the centre of the round hole through which the spindle of the handle passes through and the latter refers to the depth of the lock body which can be seen from the outside of the door.
When deciding on the kind of lock you want to use it is important to consider how you'll be using your doors. If your sliding doors swing horizontally, you'll require top-and-bottom tab lock which engages with the strikeplate and prevents it from being lifted or opened. If your patio doors open vertically, you'll need to choose a mortise latch with a spring loaded hook latch for added security.
When determining the dimensions of the lock you have It is essential to note the position of the screw holes. Some mortise locks have round screws, while others use square screws. Repair My Windows And Doors 'll need to know where the keyway is. Some locks have a vertical keyway, while others are 45-degree angled. It's a good idea to capture a picture of the lock you have in place using your digital camera before you take it off to ensure that you get the correct replacement.
After you've taken the measurements and have completed the measurements, it's time to begin looking for a new patio door lock. You can locate a wide selection of top-quality products on the internet with a variety of branded options with advanced security features to safeguard your home. It is essential to research locks and read reviews prior to you make a decision. Lastly, don't forget to clean your locks regularly to prevent dirt and debris from interfering with the function of your doors.
Pay attention to the Screw Holes
Patio doors play a crucial function in securing your home and should be inspected for signs of wear and tear to ensure they're operating properly. Over time, the locks and spindle connecting the interior and exterior handles are likely to require replacement. A strong lock will not only help stop unwanted entry, but it will also increase energy efficiency, security, and safety.
There are several ways you can narrow your search for a new lock if you don't have the specific model. To begin with, determine the type of keyway that is employed. Rectangular mortise locks that are cutouts are usually used on aluminum patio doors, while E2126 and E2079 locks are set in a recess in the frame of wood or vinyl patio doors. If you own a digital camera, uploading a picture of the lock could help in determining what type it is.
Another method to determine the type of lock you have is to examine the screw holes. The screw holes on a majority of sliding patio door locks are aligned with the latch keeper that is attached to the side jamb. However they may not be the same. Some screws are longer than others or have different threaded finishes. Some screws are equipped with washers or a hexagonal nut attached, which can change the way they fit in the lock hasp.
Once you know what type of lock your home has, you can begin preparing to replace it. It is necessary to clean the lock with a damp cloth or brush to get rid of any debris that could hinder its operation. After you've cleaned the lock, apply a silicone-based lubricant in order to ensure that the locking mechanism is smooth and quiet.
It's a great idea replace the screws you have been using with a longer one. This will allow you get more grip and will allow you to install the lock more easily. After you've completed that it's a good idea test the handle and observe how the latch engages inside the lock.
If the hasp does not engage it is possible to install a washer or hex-nut behind it to help it catch more of the door's lip. You can even add a shim to the side of the lock keeper that is on the jamb to see if it aids.
Check the Lock Snib
The snib acts as the mechanism for locking that is located inside your door handle. The snib can be turned off and on to open or close your patio doors, and is the first thing you need to look for if your locks aren't working properly. You should also examine the keepers on the top and bottom of your door frames for any misalignment or looseness that could cause them to break. Make sure your snib is properly seated and that the lock isn't snagged or blocked in any way.
The most common patio doors locks are steel mortise locks that lock sliding glass doors. Incorporated into the door frame they are available in various styles and are a great security measure. Some are designed to hold keys while others feature an oval cutout that makes it simple to lock and unlock.
Another option that is popular is a step-on lock with a thumb screw that secures your sliding doors in place without requiring you to turn the knob or use the key. These locks are commonly found on older doors with metal frames, but they can also be used to secure vinyl or wooden-framed sliding door frames.
If you look over your current patio lock, take note of the type and size screw holes used to fix the escutcheon as well as the lock body. This will allow you to select a lock with the correct screw holes. It's also a good idea to check your strike plate to ensure it's properly secured.
If you have Jason Windows boltlock sliding doors between 2000 and 2009, ensure the screws that hold the door are secure and not loose or missing. These screws keep the snib in a partially open "vent" position, which allows airflow, while also promoting security, and are important for preventing your lock from slamming. All locks must be maintained and cleaned regularly to keep dirt, dust, corrosion, or debris from obstructing their operation.
If your snib has broken, it may be possible to replace the entire strike plate and snib assemblage. If your snib just requires alignment, you can correct it by removing the strikeplate with an abrasive blade and backing out the adjustment screws (located above and beneath the screw). You will then need to move the strikeplate upwards or down until the engagement tongue is in line with the Milgard logo.