10 Quick Tips For Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 makes it simple to open doors and start your car. There are a myriad of reasons the key fob might stop working. This includes a dead coin-battery or water damage, problems with receiver modules, as well as interference.
This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob doesn't work is the battery is dead. Modern key fobs have a restricted operating range, and must be within some feet of the vehicle to function. If you're not close to your vehicle and press the key fob button the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.
If this happens, replace the battery of your coin cell (Part number CR2032) with a brand new one from a reliable brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.
You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The parking lights should blink and the key fob will operate the lock and unlock switches.
If your fob's key isn't working even after replacing the battery, it may be water damage which hinders it from connecting to the module in your vehicle. Water damage can happen in many ways, including simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture back out. If this doesn't work, your fob may need to be reprogrammed by a professional auto locksmith or by the dealer.
Water Damage
While the fob comes with rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to become shorted and eventually end up dying. It's not a good idea to get the fob wet however, but don't give it up even if you accidentally drop the fob in water or forget to remove it from your pants pocket.
Remove the battery first. Clean the electronic chip using isopropyl or a similar product and then dry it thoroughly before replacing the battery. Check the fob to check if it's working. If the fob doesn't work, it may have to be programmed again. This is usually done by an auto locksmith or dealer.
If your key is older and has not been programmed to work with your vehicle, you will need to replace it completely. This is a simple procedure that can be handled by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition in your vehicle. The locksmith also needs to reprogram your fob into the car's system. This is a cost-effective and quick process that can be completed in the same day.
Receiver Module Issues
The 500 key fob you have may be inoperable because it's out of range. The remote typically has an operating range of 30 feet or less and if it's far from your car, it won't respond to your commands. This can be easily fixed by moving it closer to your vehicle until it begins responding.
If your fob does not work after replacing the battery in the coin, also known as a "button", "watch" or "button", it could be due to a problem with the circuit board inside. Reprogramming the fob typically resolves this problem. There are instructions on how to do this for the majority of vehicles by searching YouTube or checking out the owner's manual.
It may be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, it could prevent your coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob may be out of sync with your vehicle because due to hardware or software issues. This can be a major issue, but you are able to usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In certain instances it may be necessary to install the software again in your body control module as well.
Interference
Interference can also cause the key fob not to receive or transmit a signal. replacement fiat 500 key could happen when the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob could not work due to a bad connection to the buttons or water damage, or damage to the internal chips.
If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.
There is a straightforward method to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will get rid of any residual electricity and restart the car's computers. This can help get your key fob working again. If the problem persists you should seek out an expert technician. They will be able to identify the root of any problems.