10 Of The Top Facebook Pages Of All-Time About Repair Car Keys

How to Repair Car Keys

The car keys aren't big and may not be considered important, but they are essential for the operation of your vehicle. The cost of replacing a traditional or contemporary transponder car key can range from $200 to upwards of $200.

However, there are ways to repair your car keys at home with only a fraction of the cost. This article will cover the most frequent car keys problems and their DIY solutions.

Dead Key Fob Batteries

The remote key fobs that are included with cars make it easier than ever to open the trunk, doors, and tailgate. The battery inside this device is prone to dying. There are a few strategies you can use to resolve this problem quickly.

Examine if your vehicle is still in ignition mode. If it is the battery on the key fob could be low rather than dead. To test, press the fob's button against the ignition button on the vehicle. If this is successful, the battery is probably fine and only needs to be replaced.

To replace the fob's battery, start by prying the case open using an instrument like a screwdriver, or watch-type tool. Be careful not to put too much pressure on the fob since this could cause the fob's to split in two. If the fob isn't opening Try using your pry tool more than once around the outside of case.

Once the fob is open then remove the mechanical key and then open the electronic section of the car. Then, insert the battery replacement and then snap the shell back together. If the key fob isn't working after this, there may be a larger issue with your car's remote start system that requires a professional diagnostic. If this is the case, a trusted mechanic should be able help you. automotive key repair can also reach out to roadside assistance for assistance with your vehicle in case you need it.

Broken Key Ring

There are a few steps to do in the event that your key fob won't work because the ring is broken. The first step is to see if the damaged piece is still inside the ignition. If it is, you should remove it without damaging the door lock or ignition lock. Call a locksmith if you have difficulty getting rid of the key. They have special tools that can safely remove the damaged key from the ignition.

Another reason that can lead to broken car keys is corrosion on the circuit board or plastic frame. Clean the circuit board using cotton swab. This will remove corrosion and ensure that the contact pads don't get damaged.

If your key won't start because of a broken ring it, you might be able to repair it with a strong wire or nail to seal the hole. Superglue can be used to repair a broken key ring. After cleaning the ring with a moist cloth Apply a small amount superglue to each end of the nail or wire. Allow the pieces to dry, and then press them in place. These DIY solutions may seem appealing, however they are only a temporary solution. For long-term repairs, it's recommended to work with a professional locksmith. They have the knowledge and tools to fix damaged keys quickly and effectively. They can even replace the battery inside your key fob, and reprogram it if needed.

Broken Key Blade

Some key blades can break due to a lot of wear and tear. If this happens, you should probably buy a new blade. Fortunately, the issue isn't as serious as it may appear at first. The primary issue is that the blade broke off from the case.

Spraying lubricant into the keyhole is a solution to fix the problem. Then you can use pliers tweezers, or a pin to grasp the damaged key and remove it. If the key is magnetic, you can also try using a magnet to pull it out. Just be careful not to use a magnet on an ignition key as it could cause the tumbler of the lock to break.

If you are unable to get the broken piece of key, contact a locksmith right away. They have special tools to safely extract keys without causing any further damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of glue to the edges and press them in. Then, wait until the glue has dried before you insert your key into the lock. This method isn't reliable and you might have to repeat the process multiple times before it works. Super glue may not hold the key together. Therefore, this is more of a stopgap measure rather than a permanent solution.

Broken Plastic Loop

If the loop of plastic on your key fob breaks it can render the key ineffective. Luckily, this is a fairly simple fix. You can use thick wire or a finishing nail as a replacement. Make two holes in the damaged loop of plastic at each end of the wire or nail. Cut the wire or nail to key width, then place one drop of superglue in each hole. Apply the nail or wire into the holes and allow them to dry.

A locksmith who sells replacement shells is a different option. They can transfer the programmable portion of your key into the new shell, and cut an entirely new blade at a fraction of the cost.

It's not the ideal solution, but it can help you get back on the road if your key broke in half. However, it could be difficult to repair the blade of the key if it's in the ignition. If you're not cautious you can employ a hair clip, or a needle to remove the broken part from the ignition. The best solution is to contact a locksmith who has special tools for safely removing damaged keys from the ignition. They can also make you a new key with the appropriate cuts for your vehicle's ignition to ensure that it functions correctly when inserted into the lock.

Broken Master Key

If a key is broken inside the lock, you'll have to attempt to retrieve it before it's completely destroyed. There are a few techniques you can use, including using lubricants, tools, needle nose pliers or tweezers to take a small piece of the broken key and then remove it.

To begin, spray the inside of your lock with a lubricant, such as graphite powder or WD-40. You can also use the hacksaw blade method by sliding the blade across the face of a damaged key and grasping onto a few of its teeth.' If you are successful you will be in a position to cut the damaged key.

Another helpful tool is a spiral key extractor, which you can find in many hardware stores. It is a thin flexible rod with spiral threads that can be placed in the keyway, and later bent to form the broken part of the key. Once it has gotten caught on the serrations, you can twist the bar into a circle and then pull it up against the broken section of the key.

Before contacting a locksmith try to remove the broken master key before calling a locksmith. If you are unable to get an item out, you need to call in the big guns - get a locksmith to make you a brand new key and reprogram it to the transponder in your car.