10 Mobile Apps That Are The Best For Double Glazing Door Lock Repairs
Double Glazing Door Lock Repairs
Have you noticed that your uPVC window or door mechanism started to fail? Perhaps the door or window handles don't meet up properly or are hard to use.
You'll be wasting energy if your double-glazed doors don't perform as they should. This increases the likelihood of burglaries. Owen the Locksmith will be able to repair your door lock at a reasonable cost.
Snapped Key
It can be quite frustrating when a key snaps into a lock. It's also potentially a security risk since the door might not lock and make you vulnerable to intruders. There are a few quick solutions you can use to fix the problem and get your door working again.
Be calm. If you panic you may end up pushing the damaged key piece further into the lock.
Spray WD-40 or another penetrating oil, into the lock. This will help the broken piece come out more easily. You can also use a screwdriver to break any pieces that are stuck. If you have a chunk of the key that is still sticking out then grab it using a paperclip or other thin metal object and pull it. Both methods work, but you must be careful not to push the broken key piece further into the keyway.
Some paperclips have grooved edges that can be used as hook extractors, and some jigsaw blades are also suitable for this function. If you do not have any of these handy, you can use needle-nose pliers to bend them and create hooks. Also, a pair tweezers can be used to grasp and pull out the remaining part of the broken key.
If you are unable to remove the broken key piece, use a lock deicer. It's available in many hardware stores and is used to freeze any moisture present in the lock.
If none of these solutions work, it may be time to call a locksmith. Fitlocks experts can quickly fix problems such as broken handles or broken keys with uPVC locks and door mechanisms. They can also alter the double glazing door mechanisms so that they are simpler to operate. Book a double glazing repair through us online or give us a call to discuss your requirements.
Broken Cylinder
A damaged cylinder could pose a serious security risk. A locksmith professional can repair the cylinder. To fix the cylinder, locksmiths must tap it. They can do this with the hammer or any other tools, but the most effective way is to use a long match or a piece of wire. Then, position the end of the match or wire close to the keyway. The locksmith can then hit the lock to crack it. This is more secure than using the hammer, which could cause damage to the lock.
Overheating is the most common reason behind cylinder heads cracking. This can happen when the cylinder block and head are made from different metals, like cast iron and aluminium. When St Neots double glazing repairs are heated and cool at different rates, it can create hotspots in the local area that expand faster than the rest of the cylinder head, thus leading to cracks.
Corrosion is another possible reason for cylinder fractures. If the cylinder head and the block of the cylinder are not maintained properly, this could result in corrosion or rust that could cause them to expand at more than they ought to. This can lead to cracks over time.
If your uPVC door or window lock is brittle or requires lots of pressure to turn, this can be caused by a number of things. A malfunctioning locking mechanism, misalignment, or a worn handle are common causes of this issue.
It is a quick and cost-effective fix that a majority of double glazing owners can accomplish. A professional locksmith will usually be able solve this issue within a matter of hours of arriving at your home. Depending on the needs of your home they can change the locking mechanism, change the window handles, or change the gearboxes. A locksmith with experience will always be able advise you on the most cost-effective solutions for your home. They can recommend upgrading to 3 Star TS007 Euro Cylinders, which give you an extra layer of protection from burglars. This is a small price to pay for the security that comes with knowing your uPVC doors are secure.
Broken Handle
It's not a surprise that window handle locks may break. They have complex mechanisms which deteriorate over time. It isn't easy to determine the reason for a broken window handle lock and fix it correctly.
Fixing your broken handle, whether it's the internal locking mechanism or latch can increase the security of your uPVC door and stop draughts. When you aren't doing it right, replacing or repairing your handle can be very expensive and could cause damage to the door's frame and lock and frame, so it's worth spending the time to do it right.
Screwdriver Open the window, loosen the screw holding the handle. The screw should be on the inside of the back plate, and is normally concealed by an aesthetically pleasing cover for the screw reasons. Be careful not to lose any internal components within the handle, for example the plates or levers that are on either side of the spindle. It is best to keep them in the same order so that you can re-install them in the event of a need.
Then, with another screwdriver loosen the screw that connects the handle to the spindle at the back. Once the screw is loose, you can pull the handle out and take out the broken spindle. Replace it with a brand new spindle, ensuring it's the same length (you can buy them on the internet or at hardware stores). Securely screw it in the frame. Don't over tighten the screw as this can cause damage to the handle and window frame.
Close the handle and test it. It should function smoothly, and you will be able to open your windows once again.
While you're working on the handle, don't forget to make sure your uPVC windows are closing properly. If they don't close properly, you could experience damp or draughts inside your home. Also, you could be compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be able to adjust the hinges on your window frames to ensure they shut correctly.
Broken Spindle
It is often the case that the spindle within a handle breaks rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These windows require a handle to operate an locking device within the frame of the window. The handle is connected to a central rod that activates a series of mushroom-shaped locking cams that lock into the window frame keep. If the dead latch mechanism does not open when the handle is turned, it is likely that the spindle has broken, this can be a very frustrating issue.
Luckily, there are options to rectify this issue. A reputable locksmith can swiftly and effectively fix the issue. A professional locksmith will be able to disassemble the window's handle using a tool to remove the wheel portion where the spindle is located. This is done without causing any damage to the handle or causing any other damage to the frame of the window.
After removing the wheel, the technician can examine the spindle to determine what caused it to break. This involves breaking down the spindle into its component components and carefully observing their general condition as in addition to any specific areas of damage or excessive wear. This procedure is usually performed in a clean environment by highly skilled technicians.
Next, clean the damaged spindle. This will help get rid of any dirt or other debris that might be preventing it from operating normally. After this the spindle could be repaired or replaced. If the technician is replacing the spindle, the dowel can be used that is comparable in size to the original. The technician will then make holes in the same way into both pieces. This will ensure that the spindle will fit perfectly with the handle.
If the spindle is damaged and cannot be repaired, it could require replacement completely. Home centres sell generic substitutes, but if your window design is unusual, you will have to speak with a cabinet maker or woodworker who can recreate the exact piece. Once the spindle has been installed, it can be attached to the handle. Line up the screw holes on the handle to the screws already in the frame. Once the new handle is seated you will be ready to operate your uPVC window.