10 Inspiring Images About Car Key Button Repair
Car Key Button Repair
A damaged car key button can be frustrating. You might need to call an emergency locksmith service that is available 24 hours a day for assistance or to purchase a new remote.
However, you may be in a position to save money by fixing an old key fob instead of replacing it. This is especially true if the issue is caused by the worn-out switch or defective contact.
Battery
If your key fob's buttons are not responding to your pressing them, this could be a sign that the battery is dead or is nearing its end of life. Fortunately replacing the battery is a simple task that can be completed on your own rather than hiring a locksmith or dealer to take care of it.
Find the battery compartment first. The battery compartment is usually located on the back of the key fob, and may be concealed behind a cover that can slide out or an open button that opens the access point. When the compartment is open then you will find the small cell battery. It's usually the shape of a small coin and marked with an plus and minus symbol. Remove the old battery and replace it with a brand new one. Make sure the plus and symbol are aligned correctly.
Once the battery is installed, close the compartment and snap the two parts of the key fob. Make sure to align the parts and snap them in place correctly prior to closing the door and testing your keys. Press any of the buttons to confirm that they work properly.
If your remote keyfob still isn't working after replacing the battery, there could be other problems that require a different type of repair. Physical damage caused by dropping the fob into a puddle, for instance, can sometimes cause it to cease functioning completely. Alternatively, it might be suffering from an internal electrical problem or may need to be deprogrammed by an expert or locksmith. See if you can find out if the problem is related to your key fob using these other common methods for troubleshooting your car.
Switches
Depending on the year and the model, there are a variety of kinds of switches that are found in the car keyfob. The older type of key often has a separate chip that you can see in the case, whereas the modern keys are more sophisticated and function by sending signals to the car. The buttons on a key may be damaged or worn out through regular use, irrespective of the model. The result is they become difficult to press, or even ineffective. If you try to force the button to function, it can cause further damage, and could even prevent the key from being able to start your vehicle in the future.
If you're unable to get your key to work, try changing the batteries. If that doesn't help, you may need to clean your key fob and adjust the switches. Because these tiny electronic switches spend a lot of time being tossed around they are more prone to wear out than larger components of your key.
The switches have a rubbery feeling and are coated with a film that conducts electricity. The film may be worn away over time. Fortunately, they are also tiny and affordable to replace. The older ones are soldered to the circuit board, so you'll have to take care to remove them without damaging anything else. Then you can solder the new ones in and reassemble your key fob.
One way to prevent your car key fob from getting damaged is to avoid using it for more than a few hours at a time and also to not leave it in areas in areas where it is visible. Also, make sure you find a secure place to keep your key in when you aren't making use of it.
If you've tried cleaning your key fob and replacing the battery, and the issue continues to persist it's time to consider a locksmith. A professional locksmith can test the frequency of your key to see whether it's still able communicate with your vehicle, and open and replace micro switches, swap cases and more.
If the buttons aren't able to move freely up and down the case, they could be stuck or even break. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it could be necessary to take off the case. If the contacts where the buttons touch don't fit well or are worn out, adjusting them may be the only way to fix the issue.
Rubber buttons wear out over the years. The rubber stretches, nails gouge into it and the buttons can become difficult to press. This can cause the key to fail and, in this situation, it is time for the replacement of the case or buttons. This repair involves removing the remote, then locating the buttons on the circuit board, and then heating the solder before carefully taking them off. New buttons are then attached to the circuit board. The case can then be rebuilt with the horse shoe key blade piece is attached. The new buttons should be tightly fitted into the case to prevent them from falling out.
Inner Case
Since your key fob is likely to be tossed around and sometimes be accidentally pressed, the buttons inside can be damaged or stuck over time. With the help of metallic tape and a hole-punch, you can often quickly solve this issue in the event that your vehicle isn't at home and the key fob doesn't work and allows you to open the doors, but not start the engine. This simple fix will allow you to safely get back to your car and finish your trip.